Bedienungsanleitung Hotpoint-Ariston lv 465 a bk c ha (Seite 20 von 84) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

127867

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Rinse aid and refined salt

Only use products which have been

specifically designed for dishwashers.

Do not use table salt or industrial salt, or

washing up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to

add rinse aid; however, we recommend that you add salt,

especially if you live in an area where the water is hard or

very hard. Follow the instructions given on the packaging.

If you do not add salt or rinse aid, the LOW

SALT

* and LOW RINSE AID* indicator lights will

flash continuously.

Loading the rinse aid

Rinse aid makes it easier for the crockery to dry, as water

runs off surfaces more readily and therefore does not leave

streaks or marks.

The rinse aid dispenser should be filled:

 whenever the indicator light (H) signals that it is empty.

Illuminated light: add rinse aid; unlit light: there is no

shortage of rinse aid in the dispenser.

 when the LOW RINSE AID

* indicator light on the panel

flashes;

1. Open the dispenser by turning

the lid (G) in an anticlockwise

direction.

2. Pour in the rinse aid, making sure it

does not overflow from the dispenser.

If this happens, clean the spill

immediately with a dry cloth.

3. Screw the lid back on.

NEVER pour the rinse aid directly

into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the washing or drying

results, you may adjust the quantity of rinse aid used. Use a

screwdriver to turn the dosage adjuster to one of the 6 pre-set

positions (the default position is set to 4):

 if there are bluish streaks on the crockery, set the adjuster

to a lower number (1-3).

 if drops of water remain on the crockery or there are

limescale marks present after the cycle has finished, set the

adjuster to a higher number (4-6).

If you are using multi-functional tablets and you wish to

further improve the drying performance of the appliance, fill

the dispenser and set the dosage adjuster to 2.

Loading the refined salt

Every dishwasher is equipped with a water softener which, by

using refined salt designed especially for this type of

appliance, supplies water without limescale which is then used

to wash the crockery.

This dishwasher offers a setting which helps to reduce

pollution and optimises washing performance in accordance

with the water hardness level in your area. This information can

be obtained from the organisation which supplies your

household with water.

In order to obtain the best possible results from a wash cycle,

make sure that the dispenser is never empty. Refined salt

removes limescale from the water, thus avoiding the formation

of deposits on crockery. The salt dispenser is located in the

lower part of the dishwasher (see Description) and should be

filled:

 when the green float

* cannot be seen by simply looking at

the cap of the salt dispenser;

 when the LOW SALT

* indicator light on the panel flashes;

 if your machine is not equipped with an indicator light or a

green float:

approximately every 30 wash cycles;

1. Remove the lower rack and unscrew

the cap of the dispenser (in an anti-

clockwise direction).

2. For the first wash cycle only: fill the

dispenser up to the edges with water.

3. Position the funnel

* provided correctly

(see figure) and fill the salt dispenser up

to the edges (approximately 2 kg); it is normal for a little water

to leak out.

4. Remove the funnel*, wipe away any salt residue from the

thread and screw the cap on tightly, so that detergent does

not leak into the dispenser during the wash cycle (this could

damage the water softening system beyond repair).

When necessary, measure out the salt before a wash

cycle so that any saline solution which has leaked out of the

salt dispenser is removed.

Adjusting the amount of salt*

It is possible to adjust the amount of salt used according to the

hardness of the water in your area (this information is available

from your local water board).

1. Unscrew the dispenser cap.

2. Turn the arrow on the neck of the

dispenser (see figure) towards the + or -

symbols, using the table below as a

guide.

(°dH = hardness measured in German degrees - °f =

hardness measured in French degrees - mmol/l = millimoles

per litre)

The default setting of the water softening system is +.

- If using multi-functional tablets fill the salt dispenser and set the

adjuster to -; if the hardness of the water is greater than 60°fH,

set it to +.

* Only available in selected models.

Hardness of the water

°dH °fH °mmol/l

Selector

knob

position

Salt

consumption

(grams/cycle)

Autonomy

(cycles/2 kg)

0 - 10 0 - 17 0 - 1.7 / 0 /

10 – 25

18 – 44

1.8 – 4.4

- 20 60

25 – 50

45 – 89

4.5 – 8.9

MED 40 40

> 50 > 89 > 8.9 + 60 25

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint-Ariston lv 465 a bk c ha Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info