Bedienungsanleitung Hotpoint-Ariston lv 620 bk (Seite 21 von 80) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

126826

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

ARISTON DISHWASHER - Instructions for installation and use

ISHWASHER

If the power socket

to which the

appliance is

connected is not

compatible with the

plug, replace it with

a suitable plug rather

than using adapters

or multiple plugs as

these could cause

overheating or

burns.

Installation and moving

After having bought or moved your dishwasher to another home, a correct installation

ensures that your dishwasher will operate smoothly and efficiently.

ments, use original spare parts

only.

Connect the cold water supply

hose to a 3/4 gas threaded con-

nection, placing the small filter

provided between the hose and

connection, taking care to

screw it tightly onto the tap (see

fig. 2).

If the water pipes are new or

have not been used for an

extended period of time, let the

water run to make sure that the

water is clear and free of

impurities. If this precaution is

not taken, there is a risk that the

water inlet can get blocked and

damage the appliance.

Hot water connection.

Your dishwasher can be

supplied with hot water from

the mains supply (if you have a

central heating system with

radiators) at a temperature of

no more than 60°C.

In this case, the wash cycle time

will be about 15 minutes

shorter and the wash will be

slightly less effective.

The connection must be made

to hot water supply following

the same procedures as those

indicated for the cold water

connection.

Drain hose connection.

Fit the drain pipe into a drain

line with a minimum diameter

of 4 cm or place it over the sink.

Avoid restricting or bending it.

Use the special plastic elbow

provided (see figure) to

position it in the best possible

way. The part of the pipe

marked with the letter A should

be between 40 and 100 cm

above the ground.

The pipe should not be

immersed in water.

Electrical connection.

First of all, check that the

mains voltage and frequency

values correspond to those

stated on the rating plate

located on the stainless steel

inner door of the appliance and

that the electrical system to

which the dishwasher is

connected is sized for the

maximum current indicated

on said rating plate.

Earth: indispensable

safety.

Only now can you plug the

appliance into a socket

provided with an efficient

earth connection (the system's

earthing is a guarantee of

safety provided for by law,

make sure your system has it).

Choose where you want to

install your dishwasher, you

can even place it so that its

sides or back panel are side by

side with furniture or up against

the wall. The dishwasher is

provided with water supply and

drain hoses, which can be

directed towards the left or

right to facilitate appropriate

installation.

Levelling.

Once the appliance is

positioned, adjust the feet by

screwing them in or out

depending on how high you

want it and to level it so that it

is horizontal. Make sure that it

is not inclined more than 2

degrees. If the appliance is

level, it will help ensure its

correct operation.

Adjusting the back Feet

Insert the appliance into the

cutout and then adjust the

height using the screws located

on the front bottom part of the

machine. Use a screwdriver to

turn the screws in the

clockwise or anti-clockwise

direction to increase or

decrease the height

respectively.

Cold water connection.

This electric household

appliance should be connected

to the water mains using the

cold water supply hose

provided with the appliance

only. Do not use a different

hose. In the event of replace-

Your dishwasher has arrived

The special plastic

elbow should be

fastened firmly onto

the wall to prevent

the drain hose from

moving and allowing

water to spill outside

the drain.

Fig.2

Power supply wire.

Check the power supply wire

on a regular basis; if it is

damaged, we recommend you

have it replaced by an

authorised technical Assistance

service centre.

Condensation-proof tape.

On some models, a transparent

condensation-proof adhesive

tape has been provided.

It should be stuck onto the

lower side of your wooden

worktop to protect it from the

formation of condensation.

When not provided, this tape

can be requested as a spare part

from authorised retailers.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint-Ariston lv 620 bk Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info