Bedienungsanleitung Hotpoint-Ariston TCL G31 (Seite 8 von 44) (Englisch, Portugiesisch)

479299

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Start and Programmes

Post Creasecare

When selected, the clothes are occasionally tumbled

after the end of the drying and cool tumble cycles, to

help prevent creases developing should you not be

available to remove the load immediately the programme

is complete. The light is on during this phase.

Empty Water Light / Container

(If you have plumbed your dryer to a drain this light

can be ignored, as there is no need to empty the water

container).

When this light is on (not flashing) it reminds you to

empty the water container.

If the water container fills during a programme, the

heater turns off and the dryer does a period of Cool

Tumble then the light flashes and the buzzer sounds.

You must empty the water container and restart the

dryer or the clothes will not dry. After re-starting the

dryer, the light will take a few seconds to go out.

To avoid this always empty the water container each

time you use the dryer (see Maintenance).

●

Door Opening

Opening the door (or pressing the START/PAUSE

button ) during a programme will stop the dryer

and have the following effects:

●

The START/PAUSE light flashes Amber.

●

During a delay phase the delay will continue to

count down. The start/pause button must be

pressed to resume the delay programme.

One of the delay lights will flash to show the

current delay setting.

●

The start/pause button must be pressed to

resume the programme. The progress lights will

change to show the current status and the

START/PAUSE light will stop flashing and turn green.

●

During the post creasecare phase of a drying

programme, the programme will finish. Pressing

the start/pause button will re-start a new

programme at the beginning.

●

Changing the programmes knob will select a new

programme and the START/PAUSE light will flash

green. You can use this to select the Cool Tumble

programme to cool the clothes, if you find them

dry enough. Press the START/PAUSE button to

begin a new programme.

●

Note

If you have a power cut, switch off the power or

remove the plug. When power is restored, press the

START/PAUSE button and the programme will

resume.

●

PROGRAMMES knob

! Warning, if after pressing the START/PAUSE button

, the programmes knob position has changed, the

new position will NOT change the programme selected.

To change a selected programme, press the

START/PAUSE button ,the light flashes Amber to

indicate the programme is paused. Select the new

programme and any options required, the light will

then flash green. Press the START/PAUSE button

again and the new programme will start.

●

OPTION buttons / lights

These buttons are used to customise the selected

programme to your requirements. Not all options are

available for all programmes (see Start and

Programmes). If an option is not available and you

press the button, the buzzer will beep three times. If

the option is available there will be one beep and the

option light next to the button lights to confirm the

selection.

Progress ( Drying, Cool Tumble, ) /

Delay (3hr, 6hr, 9hr) Lights

When the light next to the delay button is on, these lights

flash to indicate the delay time selected. During other

programmes they indicate the progress of the dryer,

each one comes on as the corresponding phase starts.

Time Delay

The start of some programmes (see Start and

Programmes) can be delayed for up to 9 hours in 3hr

steps. Ensure the water bottle is emptied before setting

a delayed start.

When a delayed start is in progress the light next to the

delay button will be on and the selected delay period

light will flash (after the start button has been pressed).

To set a delayed start, press the Time Delay button,

and the light next to the button will come on together

with the 3hr delay light. Pressing the button again will

advance the delay setting to 6hr, the 3hr light goes

out and the 6hr light is on. Each time you press the

button the delay setting advances 3 hours, as indicated

by the corresponding light. If the 9hr light is on,

pressing the button again will cancel the delay.

Holding in the On/Off button will also cancel.

Pre Creasecare

When a delayed start and this option have been

selected the clothes are tumbled occasionally during

the delayed period to help prevent creases developing.

High Heat

Available for Time Drying Programmes. Press this button

and a high heat setting is selected and the light next to

the button comes on. Timed programmes have a

default of low heat, if the light alongside the button is

on then pressing the button selects a low heat setting

and the light goes out.

The Controls

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint-Ariston TCL G31 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info