Bedienungsanleitung Hotpoint CE6IFA.2 X F HA (Seite 31 von 76) (Englisch, Holländisch, Französisch, Italienisch)

513525

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

 Avoid using the same cookware which has been

used on gas burners: the heat concentration on

gas burners may distort the base of the pan,

causing it not to adhere correctly.

Safety devices

Pan sensor

Each cooking zone is equipped with a pan sensor

device. The hotplate only emits heat when a pan

with suitable measurements for the cooking zone is

placed on it. If the indicator light is flashing, it may

indicate:

 An incompatible pan

 A pan whose diameter is too small

 The pan has been removed from the hotplate.

Residual heat indicators

Each cooking zone is equipped with a residual heat

indicator. This indicator signals which cooking zones

are still at a high temperature. If the power display

shows

, the cooking zone is still hot. It is

possible, for example, to keep a dish warm or melt

butter or chocolate. As the cooking zone cools, the

power display will show . The display switches off

when the cooking zone has cooled sufficiently.

Overheating protection

If the electronic elements overheat, the hob switches

off automatically and

appears on the display,

followed by a flashing number. When the

temperature has reached a suitable level, this

message disappears and the hob may be used

again.

Safety switch

The appliance has a safety switch which

automatically switches the cooking zones off after

they have been in operation for a certain amount of

time at a particular power level. When the safety

switch has been triggered, the display shows 0.

For example: the right rear hotplate is set to 5 and

will switch off after 5 hours of continuous operation,

while the front left hotplate is set to 2 and will switch

off after 8 hours.

Power level

Maximum operating

time in hours

Buzzer

This can also indicate several irregularities:

 An object (a pan, cutlery, etc.) has been placed

on the control panel for more than 10 seconds.

 Something has been spilt on the control panel.

 A button has been pressed for too long. All of the

above situations may cause the buzzer to sound.

Remove the cause of the malfunction to stop the

buzzer. If the cause of the problem is not

removed, the buzzer will keep sounding and the

hob will switch off.

Technical description of cooking zones

The induction system is the quickest existing way of

cooking. Unlike traditional hotplates where the

cooking zone heats up, with the induction system

heat is generated directly inside ferromagnetic

based pans.

Hobs

CE6IFA.1 F /HA

CE6IFA.1 X F /HA

Cooking zone

Power (W)

Back Left

I 1400  600 se Ant. Sx*

Back Right

I 2200  B 3000*

Front Left

I 2200  B 3000*

Front Right

I 1400  600 se Post. Dx*

Total power

7200

Key:

I = single induction cooking zone

B = booster: the power of the cooking zone may be

boosted to 3000W

* = the maximum power is limited to 600 W until the

booster is activated for the appropriate rear

cooking zone (see Start-up and use).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint CE6IFA.2 X F HA Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info