Bedienungsanleitung Hotpoint CM HPC (Seite 6 von 11) (Englisch)

665378

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

hotpoint.co.uk

removed as soon as the compartment is

opened. If the coffee capsule does not t into

the compartment easily, remove it and re-

place it correctly.

Insert the coffee capsule as shown in the

Figure.

Lower the movable section of the machine

head completely.

Press the lever (1) until it locks in place and

put the cup on the cup holder (7).

Touch one button:

- button 5.1 for espresso coffee delivery.

- button 5.2 for lungo coffee delivery.

The delivery will stop automatically as soon as the

set volume is reached in the cup.

The quantity of coffee poured out by

each button was determined after

carefully considering the requirements of

most users. To adjust the coffee delivery by

the different buttons based on your own taste

just follow the instructions in the next

paragraph.

The capsules are single-dose and should

not be used to make two coffees.

Remember to clean the drip tray (8) and to

empty the used-capsule tray (6). Remember to

replace the water in the tank on a regular

basis.

ADJUSTING THE QUANTITY

OF COFFEE IN THE CUP

The machine allows you to adjust the desired

quantity/volume of coffee in the small cup for the

buttons 5.1 and the cappuccino cup for 5.2.

We will only see how you can set button

5.1. To set button 5.2 just follow the

same procedure, but press button 5.2 and use

a properly-sized cup.

To adjust and store in memory a custom

quantity of coffee, the procedure is the following:

• Insert one capsule in the compartment (2).

environment and reduce power consumption when

not in use. It automatically enters into Power-Save

mode if it has not been used for 60 minutes.

Button 5.1 will start ashing slowly.

To start the machine again, touch one of the two

buttons.

Before switching off the machine, we

recommend pouring out a cup of hot

water with no capsules in the capsule

compartment (2).

To switch it off set the main switch (10) to

the “0” position. We recommend that

you never unplug the machine while it is on.

POSITIONING THE CUP

HOLDER (C)

The machine was designed to use both espresso

cups and mugs.

To adjust the height of the cup holder (7),

pull it out and then place it in the espresso cup or

mug position.

Optimum position for mugs as suitable for

lungo coffees.

Optimum position for cups as suitable for

espresso coffees.

Adjust the height of the cup holder (7)

before starting coffee delivery.

COFFEE MAKING (D)

This machine was designed to use only

“Metodo Iperespresso” Illy coffee capsules.

Do not use other coffee capsules

because they may damage the machine.

Make sure buttons 5.1 and 5.2 are lit (xed

light).

Release and lift the opening lever (1) of the

capsule compartment (2).

If there is a coffee capsule in the

compartment (2), it will be automatically

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint CM HPC Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info