Bedienungsanleitung Hotpoint DH93K S (Seite 36 von 44) (Englisch)

570609

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

PLEASE PHONE US TO REGISTER YOUR APPLIANCE AND ACTIVATE YOUR PARTS GUARANTEE ON 08448 24 24 24

Installation

Electrical Requirements

For your own safety, we recommend that your cooker

is installed by a competent person such as one who is

registered with NICEIC (National Inspection Council for

Electrical Installation Contracting). The cooker should

be installed in accordance with the latest edition of the

IEE Regulations.

Warning: This appliance must be earthed.

Electrical Connections

The installer must check that the voltage shown on

the rating plate corresponds with the house electricity

supply. The cooker must be supplied via a suitable

double pole isolating switch, having a contact

separation of at least 3mm in all poles placed in a

readily accessible position adjacent to the cooker. If

the cooker is to be wired into a connector unit, this

may be positioned behind the cooker providing the

following requirements are met:

i) The connector unit must not project from the wall

more than 25mm.

ii) The top of the connector must not be more than

130mm above floor level.

Remove the terminal cover at the rear base of the

cooker. Pass the cable through the cable clamp and

connect to the appropriate terminals provided.

Allow sufficient cable for any future servicing.

Tighten the screws on the cable clamp and replace the

cover. Make main connections in the connector unit or

cooker control unit. This appliance conforms to B.S. EN

55014 regarding suppression of Radio and Television

reception interference.

A double Pole control switch having a minimum rating

of 32 amps should be used to feed the cooker using

a suitably rated cable. Where a hob is fitted adjacent

to or over the cooker, a 45 amp Double Pole control

switch should be used to feed both units via separate

suitably rated cables.

We recommend a minimum of 4mm2 PVC insulated

twin and earth cable conforming to B.S. 6004 for

connection of each appliance.

In all cases adhere to routing details (see fig. 4).

This appliance must not be installed over any other

appliance that generates heat such as a plinth heater.

Note: Due to many different types of installation, a

mains cable is not supplied with this product. The

installer will fit the correct type and length of cable.

Important

It is essential that the lower cupboard is constructed

in the manner illustrated i.e. having side, back, and

roof panels so joined as to provide no apertures which

could permit access to the oven unit when installed.

1. General

The appliance is designed for mounting at a safe level

into an oven housing which must be secured to the

backing wall.

2. Ventilation

a. The oven housing unit cabinet dimensions must

comply with fig. 4.

b. An air gap of 50mm minimum must be provided at

the rear of any top or bottom cupboards or shelves

(see fig. 1).

c. It is necessary that the cabinets are provided with

unobstructed ventilation, i.e. from adjacent cabine-

try. This can be done by either raising the base of

the cabinets using the adjusting feet (or spacers)

or alternatively by providing a slot in the cabinet

plinth to the dimensions in fig. 1.

d. The air gap at rear allows the warmed air to pass out

of the inner cabinet space. Where it is intended to fit

cupboards above the oven unit to ceiling height, it is

essential that the warmed air is exhausted through

the front of the cabinet (see fig. 1).

e. If an oven unit is installed adjacent to a tall cabinet,

steam escaping from the oven when the door is

opened could condense on and maybe stain the

adjacent surface. To prevent permanent staining,

the adjacent surface should be made of a material

that is heat resisting and easy to clean. Adjacent

tall cabinets should not be deeper than the oven

housing cabinet.

3. Final Installation

a. Using a spirit level, check that the housing cabinet

is level from side to side and from front to back in

its installed position.

b. Correct any unevenness by placing spacers under

the bottom of the cabinet. Make sure that the cabi-

net rests firmly on the floor without rocking.

c. Before the oven is fitted, the cabinet must be firmly

secured to the backing wall for stability.

d. The oven unit should now be lifted (this is a two

person lift) into the cabinet and pushed fully home.

e. Finally, the oven is secured to the cabinet by means

of the four Phillips C/SK Head screws - two through

each side trim.

f. Remove all packaging material from the grill and

oven interior.

List of loose items:

4 x Phillips C/SK Head No. 6 x 25mm screws.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint DH93K S Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info