Bedienungsanleitung Hotpoint LDFA 12H141 X EU (Seite 9 von 84) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch, Polnisch)

513518

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Rinse aid and refined salt

Only use products which have been

specifically designed for dishwashers.

Do not use table salt or industrial salt, or

washing up liquid.

Follow the instructions given on the packaging.

If using a multi-functional product it is not necessary to

add rinse aid; however, we recommend that you add salt,

especially if you live in an area where the water is hard

or very hard. Follow the instructions given on the

packaging.

If you do not add salt or rinse aid, the LOW

SALT

* and LOW RINSE AID* indicator lights

remain lit.

Measuring out the rinse aid

Rinse aid makes it easier for the crockery to dry, as water

runs off surfaces more readily and therefore does not leave

streaks or marks.

The rinse aid dispenser should be filled:

• When the LOW RINSE AID* indicator light on the control

panel is illuminated;

1. Open the dispenser by turning the

lid (G) in an anticlockwise direction.

2. Pour in the rinse aid, making sure it

does not overflow from the

dispenser. If this happens, clean the

spill immediately with a dry cloth.

3. Screw the lid back on.

NEVER pour the rinse aid directly

into the appliance tub.

Adjusting the amount of rinse aid

If you are not completely satisfied with the drying results,

you may adjust the quantity of rinse aid used. Use a

screwdriver to turn the dosage adjuster (F) to one of the 6

pre-set positions (the default position is set to 4):

• If there are streaks on the crockery, set the adjustment

device to a lower number (1-3).

• If drops of water remain on the crockery or if there are

limescale marks present after the cycle has finished, set

the adjuster to a higher number (4-6).

Setting the water hardness

Every dishwasher is equipped with a water softener which, by

using refined salt designed especially for this type of

appliance, supplies water without limescale which is then used

to wash the crockery.

This dishwasher offers a setting which helps to reduce

pollution and optimises washing performance in accordance

with the water hardness level in your area. This information can

be obtained from the organisation which supplies your

household with water.

- Switch on the appliance by pressing the ON/OFF button.

- Press the

P button and hold for a few seconds; two short

beeps will sound, The text "

WATER HARDNESSWATER HARDNESS

WATER HARDNESS" will appear

on the display and the set hardness number will also flash

slowly on the display (the water softening system is set by

default to number

3).

- Press the DELAYED START button (levels 1 to 5) or the

HALF LOAD button (levels 5 to 1) repeatedly, until the

desired hardness level has been reached (1-2-3-4-5

*, see

hardness table). You will be able to scroll through a maximum

of 5 levels. Press the

P button to confirm.

To exit the function, wait a few seconds or press one of the

option buttons

*, or switch off the machine using the ON/OFF

button.

Even if using multi-functional tablets, the salt dispenser should

still be filled.

(°dH = hardness measured in German degrees - °f =

hardness measured in French degrees - mmol/l = millimoles

per litre)

Measuring out the refined salt

In order to achieve the best possible results using a wash

cycle, make sure that the dispenser is never empty.

Refined salt removes limescale from the water, thus

avoiding the formation of deposits on crockery.

The salt dispenser is located in the lower part of the

dishwasher (

see Description

) and should be filled:

• When the green float

* cannot be seen by simply looking at

the cap of the salt dispenser.

• When the LOW SALT

* indicator light on the control panel is

illuminated;

1. Remove the lower rack and unscrew

the container cap (anticlockwise).

2. The first time you do this: fill the water

tank right up to its edge.

3. Position the funnel

* (

see figure)

and fill

the salt container right up to its edge (this should hold

approximately 1 kg); it is not unusual for a little water to leak

out.

4. Remove the funnel* and wipe any salt residue away from

the opening; rinse the cap under running water and then

screw it on, the head facing downwards so as to let the

water flow out of the four cracks which are arranged in a

star shape on the lower part of the cap. (the container cap

with the green float

It is advisable to perform this procedure every time you

add salt to the container.

Make sure the cap is screwed on tightly, so that no

detergent can get into the container during the wash cycle

(this could damage the water softener beyond repair).

When necessary, measure out the salt before a wash

cycle so that any saline solution which has leaked out of the

salt dispenser is removed.

* Only available in selected models.

Water Hardness Table

Average salt container

capacity duration

Level

°dH

°fH

mmol/l

months

1 0 - 6 0 - 10 0 - 1

7 months

2 6 - 11 11 - 20 1,1 - 2

5 months

3 12 - 17 21 - 30 2,1 - 3

3 months

4 17 - 34 31 - 60 3,1 - 6

2 months

34 - 50

61 - 90

6,1 - 9

2/3 weeks

For values between 0°f and 10°f, we do not recommend the

use of salt.

this setting may cause a slight increase in the duration of

the cycles.

for 1 wash cycle per day.

Hotpoint LDFA 12H141 X EU Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info