Bedienungsanleitung Hotpoint LSFF 8M126 Slim (Seite 4 von 16) (Englisch)

670980

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Installation

If the appliance must be moved at any time, keep it in an

upright position; if absolutely necessary, it may be tilted onto its

back.

Positioning and levelling

1. Position the dishwasher on a level sturdy floor. If the floor is

uneven, the front feet of the appliance may be adjusted until it

reaches a horizontal position. If the appliance is levelled correctly,

it will be more stable and much less likely to move or cause

vibrations and noise while it is operating.

2. Before recessing the dishwasher, stick the adhesive

transparent strip* under the wooden shelf in order to protect it

from any condensation which may form.

3. Place the dishwasher so that its sides or back panel are in

contact with the adjacent cabinets or the wall. This appliance can

also be recessed under a single worktop*

(see the Assembly

instruction sheet)

4*. To adjust the height of the rear foot, turn the red hexagonal

bushing on the lower central part at the front of the dishwasher

using a hexagonal spanner with an opening of 8 mm. Turn the

spanner in a clockwise direction to increase the height and in an

anticlockwise direction to decrease it.

(see Building-in instruction

sheet attached to the documentation)

The dishwasher meets the requirements set out by the regulations

in force concerning safety and electrical equipment.

Any technical checks should be conducted exclusively by a

trained and authorised technician: Repairs carried out by

unaithorised persons will invalidate the guarantee, as well as

posing a potential hazard to the user.

The manufacturer declines all responsibility for damage to

persons or property resulting from failure to observe the above

precautions, from tampering with even a single component or

from the use of non-original spare parts.

Connecting the water supply

Adaptation of the water supply for installation should only be

performed by a qualified technician.

The water inlet and outlet hoses may be positioned towards the

right or the left in order to achieve the best possible installation.

Make sure the dishwasher does not bend or squash the hoses.

Connecting the water inlet hose

• To a 3/4” cold or hot water connection point (max. 60°C).

• Run the water until it is perfectly clear.

• Screw the inlet hose tightly into position and turn off the tap.

If the inlet hose is not long enough, contact a specialist store

or an authorised technician

(see Repairs and After Sales)

The water pressure must be within the values indicated in

the Technical Data table - otherwise the dishwasher may be

function properly.

Make sure the hose is not bent, compressed or kinked.

DO NOT overtighten the hose connector, hand tight is

sufficient.

Tap connections*: A range of adaptors are available to suit

your tap.

Connecting the drain hose

Connect the drain hose (without bending) to a drain duct with a

minimum diameter of 2 cm. (A)

The drain hose connection must be at a height ranging from 40

to 80 cm (from 15’’ to 31’’) from the floor or surface where the

dishwasher rests.

• before connecting the drain hose, remove any internal

restrictions; this will prevent a build up of debris which could

cause a blockage.

• remove any restrictions from the waste spigot and ensure that

the sealing bung is removed (B).

It MUST NOT be connected to a surface water drain.

Ensure the drain hose is securely

attached, to prevent it coming away

while the machine is in use and

causing a flood.

Fit hose to waste securely using

a “Jubilee” type clip.

Anti-flooding protection

To ensure floods do not occur, the dishwasher:

- is provided with a special system which blocks the water supply

in the event of anomalies or leaks from inside the appliance.

Some models are also equipped with the supplementary safety

device New Acqua Stop*, which guarantees anti-flooding

protection even in the event of a supply hose rupture.

WARNING: HAZARDOUS VOLTAGE!

Under no circumstances should the water inlet hose be cut as it

contains live electrical parts.

Electrical connection

Before inserting the plug into the electrical socket, make sure that:

• The socket is earthed and complies with current regulations;

• the socket can withstand the maximum load of the appliance

as shown on the data plate located on the inside of the door

(see chapter Description of the appliance);

• The power supply voltage falls within the values indicated on

the data plate on the inside of the door.

• The socket is compatible with the plug of the appliance. If

this is not the case, ask an authorised technician to replace

MIN 40 cm

MAX 80 cm

* Only available in selected models.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint LSFF 8M126 Slim Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info