Bedienungsanleitung Hotpoint LSFF 8M126 Slim (Seite 10 von 16) (Englisch)

670980

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Detergent and

dishwasher use

Measuring out the detergent

Good washing results also depend on the correct amount of

detergent being used. Exceeding the stated amount does not

result in a more effective wash and increases environmental

pollution.

The amount can be adjusted to the soil level.

In the case of normally soiled items, use approximately either

25g (powder detergent) or 25ml (liquid detergent). If tablets

are used, one tablet will be enough.

If the crockery is only lightly soiled or if it has been rinsed

with water before being placed in the dishwasher, reduce the

amount of detergent used accordingly.

For good washing results also follow the instructions shown

on the detergent box.

For further questions please ask the detergent producers.

Open the detergent dispenser using button D and measure out

the detergent according to the Table of wash cycles:

• powder or liquid: compartments A

(wash detergent) and B (pre-wash

detergent)

• tablets: when the cycle requires

1 tablet, place it in compartment A

and close cover C; when it requires

2 tablets, place the second tablet

on the bottom of the appliance.

Remove detergent residues from the edges of the compartment

and close cover C until it clicks.

The detergent dispenser automatically opens up at the right time

according to the wash cycle.

If all-in-one detergents are used, we recommend using the TABS

option, because it adjusts the cycle so that the best washing and

drying results are always achieved.

Only use detergent which has been specifically designed

for dishwashers.

DO NOT USE washing up liquid.

Using excessive detergent may result in foam residues

remaining in the machine after the cycle has ended.

To achieve the best washing and drying results, the combined

use of detergent, rinse aid liquid and refined salt is required.

We recommend using detergents that do not contain

phosphates or chlorine, as these products are harmful

to the environment.

Starting the dishwasher

1. Turn the water tap on.

2. Press the ON/OFF button.

3. Open the door and pour in a suitable amount of detergent

(see Measuring out the detergent.)

4. Load the racks

(see Loading the racks)

and close the door.

5. Select the wash cycle in accordance with the type of

crockery and its soil level

(see Table of wash cycles)

pressing the P button.

6. Select the wash options

(see Options).

7. Press the Start/Pause button to start the cycle (fixed light):

a long beep signals the start of the wash cycle, the cycle

indicator lights up and the display shows the cycle number

and the time remaining until the end of the cycle.

8. Two short beeps and one long beep indicate the end of the

wash cycle, the Start/Pause button switches off and the word END

appears on the display. Switch off the appliance by pressing

the ON/OFF button.

9. Wait for a few minutes before removing the crockery - to

avoid burns. Unload the racks, beginning with the lower level.

The machine will switch off automatically during long

periods of inactivity in order to minimise electricity

consumption.

AUTO WASH CYCLES: some models of dishwasher are

equipped with a special sensor which can be used to assess the

level of soiling and automatically select the most efficient and

economic wash cycle accordingly. The duration of the auto wash

cycles may vary due to the operation of the sensor.

Changing a wash cycle in progress

If a mistake was made in the wash-cycle selection process, it is

possible to change the cycle provided that it has only just begun:

Once the wash cycle has started, in order to change the wash

cycle switch off the machine by pressing and holding the ON/

OFF/Reset button. Switch it back on using the same button and

select the desired wash cycle and options.

Adding extra crockery

Press the Start/Pause button and open the door, taking care to

avoid the escaping steam. Then place the crockery inside the

dishwasher. Press the Start/Pause button: The cycle will start

again after a long beep has been emitted.

If the delayed start has been set, at the end of the countdown

the wash cycle will not start. It will stay in Pause mode.

Press the Start/Pause button to pause the machine; the wash

cycle is stopped.

At this stage the wash cycle cannot be changed.

Accidental interruptions

If the door is opened during the wash cycle or there is a power

cut, the cycle stops. It starts again from the point at which it

was interrupted once the door has been shut or the electricity

supply restored.

* Only available in selected models.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint LSFF 8M126 Slim Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info