Bedienungsanleitung Hotpoint TCD 93B 6H (Seite 4 von 88) (Englisch, Französisch, Portugiesisch, Spanisch)

512833

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

Installation

Before you start using your dryer

Once you have installed your dryer and before you

use it, clean the inside of the drum to remove any dust

that could have accumulated during transport.

Where to put your dryer

●

Place your dryer at a distance from gas ranges,

stoves, heaters, or cook tops because flames can

damage the appliance.

●

If you are going to install the

appliance under a work

counter, be sure to leave a

10mm space between the

top and any other objects

on or above the machine and

a 15mm space between the

sides and lateral furnishings

or walls.

This is to ensure proper air circulation.

Ventilation

When the dryer is in use, there has to be adequate

ventilation. Make sure you put your dryer in an

environment that is not damp and has proper air

circulation throughout. Airflow around the dryer is

essential to condense the water produced during the

washing, the dryer will not operate efficiently in an

enclosed space or cupboard.

! If using the dryer in a small or cold room some

condensation could be experienced.

! We do not recommend that the dryer is installed in a

cupboard but the dryer must never be installed

behind a lockable door, a sliding door or a door with a

hinge on the opposite side to that of the dryer door.

Water drain

If your dryer is installed next to a drain the water can be

plumbed into this drain. This does away with the need to

empty the water container. If the dryer is stacked onto or

installed next to a washing machine it can share the same

drain. The height of the drain must be less than 3' (1m)

from the bottom of the dryer.

Remove hose from position shown

(see diagram).

Fit a suitable length of hose to the

new location shown (see diagram).

! Make sure that the hose is not squashed or kinked when

the dryer is in its final location.

Electrical connections

Make sure of the following before you insert the plug

into the the electrical socket:

●

The socket must be grounded.

●

The socket must be able to sustain the machines

maximum power, which is indicated on the rating

label (see Dryer Description).

●

Power voltage must be within the values indicated

on the rating label (see Dryer Description).

●

The socket must be compatible with the dryers plug.

Should this not be the case, replace the plug or the

socket.

! The dryer must not be installed outdoors, even if the

space is sheltered. It can be very dangerous if it is

exposed to rain or storms.

! Once installed, the dryers electrical wire and plug

must be within easy reach.

! Do not use extension cords.

! The power cord must not be bent or squashed.

! The power supply cord should be checked periodically

and replaced by a cord specially prepared for this dryer

and fitted only by authorised technicians (see Service).

New or longer power cords are supplied at an extra

charge by authorised dealers.

! The manufacturer denies any responsibility should

any of these rules not be followed.

! If in doubt about any of the above consult a

qualified electrician.

Minimum gap 10mm

Minimum gaps

15mm

Remove hose from

here...

...fit new hose here.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint TCD 93B 6H Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info