Bedienungsanleitung Hotpoint TCD G51 XB (Seite 25 von 36) (Englisch, Französisch)

513484

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

The Display

Start and Programmes

Warnings

The second line of the display also gives warnings and reminders:

(reminders occur at the end of the programme)

END OF CYCLE, CLEAN FILTER AND EMPTY WATER BOTTLE

●

Reminder that the water container should be

emptied and the filter cleaned every time you use the

dryer (see Maintenance).

EMPTY WATER BOTTLE

●

Indicates that the water container is full. The

message will take a few seconds to go out after

replacing the empty water container; the dryer

must be running for this to happen (see The

Controls).

Note: If the water container fills and this message

is displayed, the heat is turned off and your

clothes will not dry.

CLEAN CONDENSER, FILTER AND EMPTY WATER BOTTLE

●

This message indicates that you must clean the

Condenser unit (see Maintenance) and will occur

at intervals depending how much you have used

the dryer. When you finish the next programme the

message is cancelled. You must also clean the filter.

Choosing a programme

1. Plug the dryer into the electrical socket.

2. Sort your laundry according to fabric type (see

Laundry).

3. Open the door and make sure the filter is clean

and in place and the water container is empty and

in place (see Maintenance).

4. Load the machine and make sure items are not

in the way of the door seal. Close the door.

5. If the Display is not lit: Press the ON/OFF button

6. Press the Programmes Selection button that

corresponds with the type of fabric being dried by

checking the Programmes Table (see Programmes)

as well as the indications for each type of fabric (see

Laundry).

- If the button is selected; steps 7 and 8 are not

required (see below).

7. Choose Timed Drying or Dryness Levels option:

- If Timed Drying press and release the Timed

button until the required time is displayed.

or - To change from default dryness setting, press

and release the Dryness Levels button until

required level is indicated.

! See Programmes Table, for more details:

availability of Dryness Levels, Timed Dry and

Options.

8. Set a delay time and other options if necessary

(see The Display).

9. Press the Start/Pause button to begin.

The display will show the estimated time to end.

During the drying programme, you can check on

your laundry and take out items that are dry while

others continue drying. When you close the door

again, press the Start/Pause button in order to

resume drying.

10. During the last few minutes of Drying Programmes,

before the programme is completed, the final COOL

TUMBLE phase is entered (fabrics are cooled),

this phase should always be allowed to complete.

11. At the end of the drying cycle a message is

displayed:

- If

END OF CYCLE, CLEAN FILTER AND EMPTY WATER BOTTLE

is shown, the buzzer will beep 3 times (Note: If

the SOUND option was selected the buzzer

beeps 3 times every 30 seconds for 5 minutes).

- If

END OF CYCLE, CREASE CARE is shown, Post

Care option has been selected and if you do

not remove the laundry immediately, the dryer

will tumble occasionally for 10 hours or until

you open the door, the buzzer will beep 3

times to confirm the programme is completed.

12. Open the door, take the laundry out, clean the filter

and replace it. Empty the Water Container and

replace it (see Maintenance).

13. Unplug the dryer.

My Cycle button:

First time you press this button the display will show PRESS AND HOLD TO STORE

After selecting your favorite programme and options you can save these settings by pressing and holding in the

My Cycle button for at least 5 seconds, the top line will show a flashing followed by the selected programme. The

buzzer will then beep and the second line of the display shows

MEMORY

The next time you need this programme press the button, then the Start/Pause button and this programme will run.

If you wish, you can change your stored favorite, by selecting a new programme and/or options and press and hold

in the button (as above).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotpoint TCD G51 XB Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hotpoint TCD G51 XB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info