Bedienungsanleitung Hotto Boiler (Seite 20 von 46) (Deutsch, Englisch, Holländisch, Französisch)

669344

Zoom out

Zoom in

Vorherige Seite

1/46

Nächste Seite

Stap 13: Place the insulation part (M) around the boiler’s boiling water hose connection.

Fixate the insulation with the accompanied tie wrap.

Then open the main water tap and the stop valve (O7) of the safety group. Fill

the Hotto boiler with cold water by opening the boiling water knob until no more air is

coming out of the tap. This may take a few minutes. After the boiler has been lled with

water you must fully open the lever for hot water (K2). Allow the water to ow until no

more air is coming out of the tap. Then insert the plug in the wall socket.

Important: In the unlikely event that the device is connected to the mains power supply

without being lled with water, or if for some reason the device switches off after a short

while, please disconnect the plug from the wall socket to allow the device to cool down.

It may be necessary to reset the boiler: See the troubleshooter.

3. User instructions

The device must be lled with water before connected to the electrical supply!

The device should always be connected to a safety group!

Implementation (step 16)

The boiler is switched on with the switch (B5) on the rear, after the boiler has been fully

lled with water. The boiler is now standby and is not yet heating. You will see that the

LED at the front turns orange.

70° C setting (step 17)

Press the standby key (B3) once and the water will be heated to a maximum of 70°C.

The left blue LED will light until the temperature has been reached, after which the LED

will turn red.

100° C setting (step 17)

Press the standby key (B3) once more, and the water will be heated to 100°C. Now the

right LED will turn blue and then red once the temperature has been reached.

Setting the temperature for hot water (step 18)

The hot water temperature can be adjusted by turning the round knob (B4) at the front

of the boiler to the right (lower temperature) or to the left (higher temperature). The

setting range is 35 - 70 °C, if the boiler is set to 100 °C. The setting range when the boil-

er is set to 70 °C is 35 - 60 °C.

Using the tap (step 14/15)

• Cold and hot water

With the lever (K2) in vertical position, the tap will provide cold water. You will only get

hot water if the lever is moved towards the front. In this way no hot water and energy is

wasted.

• Boiling water

In order to get boiling water you must rst push in the catch (15.1) and then rotate the

boiling water knob (K1) away from you (15.2). When you let go of the knob (K1), the

built in spring will make sure that it will return to its original position immediately. This

feature will prevent curious children from activating the boiling water tap by accident.

UKUK

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hotto Boiler Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hotto Boiler

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info