Bedienungsanleitung Hozelock 2490 (Seite 6 von 42) (Alle Sprachen)

661705

Zoom out

Zoom in

Vorherige Seite

1/42

Nächste Seite

MUST BE WALKED BACK TO THE REEL.

To prevent damage or injury:

! DO NOT:

Let go of the hose while

rewinding. Always walk back to the reel holding the

hose.

Let go of the hose unless the

automatic latch mechanism is engaged.

Place fingers or objects in the hose aperture of the reel

during

operation.

Attempt to remove the screws from any part of the

casing.

! DO:

Remove the reel from the wall in winter to prevent

frost damage.

Keep the floor/ground below the reel as clear as

possible from water to minimise any risk of slipping.

Turn the tap off when not in use.

Fig 6.

If the hose doesn’t rewind properly when the tap is on:

! Depressurise the hose, either by allowing water to flow

through it while walking the hose end back to the reel

or by turning off the water supply to the hose.

! Lift the hose end above waist height if retraction loses

power in the last few metres.

! Walk the hose end back to the reel as shown in fig 6.

If the safety lock lever cannot be engaged when the

hose is fully re-wound, pull the hose out until you hear

one of the four clicks. The hose is now held in place

and the safety lock lever can be engaged.

Fig 7.

Leaks from inside the reel

If water leaks from the water inlet side, lift the side disc

by putting a flat ended screwdriver in the slot.

If the leak is from the hose connector, tighten the hose

nut.

If the leak is from beneath the hose connector, follow

these instructions.

1. Remove the two screws holding the hose connector.

2. Remove and replace the “O” ring (spare part no

Z73045). Grease the “O” ring using petroleum jelly.

3. Tighten the hose nut.

4. Re-assemble.

Tension adjustment

The spring tension is factory pre-set and will not require

any adjustment.

Hose replacement

If the 20m watering hose becomes damaged, do not

attempt to repair it. Contact Hozelock Consumer

Services for a replacement kit and instructions,

requesting spares number Z21915.

Wall bracket kit

If the wall bracket or pivot tube become damaged, a

replacement kit is available, requesting spares number

Z21925.

For product advice and spares, please contact:

Hozelock Consumer Services,

Hozelock Ltd., Midpoint Park, Birmingham B76 1AB

Tel: 0121 313 1122

www.hozelock.com

This Auto Reel is guaranteed for 2 years against faults

arising from defective manufacture or materials.

The hose is guaranteed for 15 years against defective

manufacture or materials.

The Auto Reel can be returned to Hozelock for repairs

and service, even after the guarantee has expired, for

prices and details please visit

www.hozelockservice.com

Please keep your purchase receipt.

(Fig.1)

A. 93273 - Dévidoir AutoReel

B. 83360 - Fixation murale

C. 93411 - Tuyau d’alimentation

D. 2175 - Raccord de robinet fileté

E. 2166 - Raccord d’extrémité de tuyau

F. 2185 - Raccord d’arrêt

G. 53025 x4 - Chevilles

H. 53112 x4 - Vis

I. 2292 - Embout de tuyau

J. 83304 - Disque Latéral

OUTILS NECESSAIRES:

Un tournevis plat

Tournevis cruciforme

Un miètre

Tips

Important

Advice

Guarantee

Contenu

Maintenance

Assemblage et Installation du

Devidoir Retractable

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hozelock 2490 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info