669388
47
Zoom out
Zoom in
Vorherige Seite
1/70
Nächste Seite
Software and configuration utilities
BIOS Setup Utility
Use the embedded BIOS setup utility to perform a wide range of configuration activities including:
Configuring system devices and installed options
Displaying system information
Selecting the primary boot controller
Configuring memory options
Boot options
Near the end of the boot process, the boot options screen is displayed. This screen is visible for several
seconds before the system attempts to boot from a supported boot device. During this time, you can do
the following:
Access BIOS Setup Utility by pressing the Esc/Delete key.
Access Boot screen by pressing the F7 key.
Force a PXE Network boot by pressing the F12 key.
Re-entering the server serial number and product ID
After replacing the system board, you must re-enter the server serial number and product ID.
Procedure
1. To enable SPD Write:
a. During the server startup sequence, press the Delete or Esc key to access the BIOS Setup menu.
b. Select Chipset > PCH-IO Configuration, and then press the Enter key.
c. Select SPD Write Disable and press Enter.
d. To enable SPD Write, select Disable and press Enter.
e. To exit Chipset, press the Esc key.
f. Select Save & Exit > Save Changes and Exit, and press Enter.
g. To save changes, select Yes. The server automatically reboots.
2. To enter the product ID:
a. During the server startup sequence, press the Delete or Esc key to access the BIOS Setup menu.
b. Select Advanced > System FRU Information, and then press the Enter key.
c. Select FRU update Support and press Enter.
d. Select Enable and press Enter.
e. Select Modify Product Part/Model Number and press Enter.
Enter the Modify Product Part/Model Number and press Enter.
f. Select Modify Product S/N and press Enter.
Enter the Modify Product S/N and press Enter.
g. Select Start Update FRU and press Enter.
h. Select Enable and press Enter. The following warning appears:
If you enable this item, the data will be written in FRU.
i. To clear the warning, press Enter. The following message appears:
FRU has been updated. Please reboot and check it.
j. To clear the message, press Enter. The following warning appears:
Please enable the setting of SPD Write Disable for security.
Software and configuration utilities 47
47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für HP Gen9 ML10 ProLiant H wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info