Bedienungsanleitung HP LASERJET4PLUS (Seite 21 von 58) (Englisch)

20204

Zoom out

Zoom in

Vorherige Seite

1/58

Nächste Seite

2 Guidelines for using media 15

Recommendations

● Regularly inspect your labels after printing for any indication that the label edges are

lifting or that adhesive contamination is occurring on the print surface. If either of these

problems is observed, HP recommends that you discontinue use of that box or

lot-number of labels and discuss the problem with your label supplier.

● If many sheets of labels are being continuously run, periodically run several sheets of

paper through the printer to clean any contamination or label-stock adhesive that

might have deposited.

CAUTION Make sure to run full sheets of labels. Reprinting unused portions can increase the risk of

the labels peeling and the occurrence of adhesive contamination.

Property Specifications

Adhesives Adhesives must not be on any external surfaces of the label before,

during, or after printing. Label construction, adhesive release strength,

and appropriate die-cutting must prevent labels from peeling off during

printing.

Different adhesives can provide removable, permanent, or

semi-permanent fixing of the face sheet onto the item being labeled.

Generally, acrylic-based adhesives are preferred for laser printing

because they can be applied in very thin layers to prevent oozing and

contamination, and can be made compatible with the heat and

pressure of fusing.

Improved processes are being developed to minimize adhesive

contamination, such as zone coating or stripped matrix. Zone coating

recesses the adhesive around the border of a die-cut, and stripped

matrix prevents adhesive from oozing between the die-cut labels. The

adhesive and liner must provide adequate release strength so that

labels will not peel off during printing.

Caliper The caliper must not exceed 0.23 mm (9.0 mils).

Face sheet The face sheet is the printable surface on a sheet of adhesive labels

and can be made from different materials, including paper, polyester,

and vinyl. It is common for a face sheet to be die-cut so that individual

shapes can be removed after printing. Polyester and vinyl labels

require a topcoat to provide the proper electrical and toner adhesion

properties. It is important to purchase labels from a knowledgeable

converter who is familiar with these processes and laser printing.

Fusing compatibility All inks, adhesives, and other materials that are used in the label

construction must be compatible with the heat and pressure of the

fusing process. Materials must not scorch, melt, ignite, offset

materials, or release undesirable emissions when heated to

205° C(401° F) for 0.1 second (0.2 second for

HP color LaserJet printers).

Liner The liner is the carrier sheet for the label material. The liner must

provide stability for the reliable pickup and transport of the label stock

through the printer.

Packaging The labels should be delivered in moisture-proof wrap to preserve their

properties.

Shelf life The labels should have a minimum shelf life of one year, when stored

at 23° C (73° F) and 50 percent relative humidity.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

HP LASERJET4PLUS Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info