Bedienungsanleitung HP OfficeJet 6951 (Seite 125 von 174) (Englisch)

655144

125

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

●

Checks that the phone cord is plugged into the correct port

●

Checks for a dial tone

●

Tests the status of your phone line connection

●

Checks for an active phone line

To test fax setup via the printer control panel

1. Set up the printer for faxing according to your particular home or oice setup instructions.

2. Make sure the cartridges are installed and that full-size paper is loaded in the input tray before starting

the test.

3. From the printer control panel display, on the Home screen, touch Fax, touch Setup , touch Setup

Wizard, and then follow the onscreen instructions.

The printer displays the status of the test on the display and prints a report.

4. Review the report.

●

If the fax test failed, review the solutions below.

●

If the fax test passed and you are still having problems faxing, verify that the fax settings listed in

the report are correct. You can also use HP's online troubleshooting wizard.

What to do if the fax test failed

If you ran a fax test and the test failed, review the report for basic information about the error. For more

detailed information, check the report to see which part of the test failed, and then review the appropriate

topic in this section for solutions to try.

The "Fax Hardware Test" failed

●

Turn the printer o by pressing (the Power button) located on the front left side of the printer and

then unplug the power cord from the back of the printer. After a few seconds, plug the power cord in

again, and then turn the power on. Run the test again. If the test fails again, continue reviewing the

troubleshooting information in this section.

●

Try to send or receive a test fax. If you can send or receive a fax successfully, there might not be

a problem.

●

If you are running the test from the Fax Setup Wizard (Windows) or HP Utility (OS X), make sure the

printer is not busy completing another task, such as receiving a fax or making a copy. Check the display

for a message indicating that the printer is busy. If it is busy, wait until it is nished and in the idle state

before running the test.

●

Make sure you use the phone cord that came with the printer. If you do not use the supplied phone cord

to connect from the telephone wall jack to the printer, you might not be able to send or receive faxes.

After you plug in the phone cord that came with the printer, run the fax test again.

●

If you are using a phone splitter, this can cause faxing problems. (A splitter is a two-cord connector that

plugs into a telephone wall jack.) Try removing the splitter and connecting the printer directly to the

telephone wall jack.

After you resolve any problems found, run the fax test again to make sure it passes and the printer is ready

for faxing. If the Fax Hardware Test continues to fail and you experience problems faxing, contact HP

support. Go to www.support.hp.com . This website provides information and utilities that can help you correct

112 Chapter 10 Solve a problem ENWW

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

HP OfficeJet 6951 Seite 125

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von HP OfficeJet 6951

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info