Bedienungsanleitung HP Photosmart 2700 series (Seite 185 von 241) (Englisch)

472677

185

Zoom out

Zoom in

Vorherige Seite

1/241

Nächste Seite

plug in the phone cord that came with your HP all-in-one, run the fax test

again.

● Make sure you have correctly connected the HP all-in-one to the telephone

wall jack. Using the phone cord supplied in the box with your HP all-in-one,

connect one end to your telephone wall jack, then connect the other end to the

port labeled "1-LINE" on the back of your HP all-in-one. For more information

on setting up your HP all-in-one for faxing, see Fax setup.

● If you are using a phone splitter, this can cause faxing problems. (A splitter is a

two-cord connector that plugs into a telephone wall jack.) Try removing the

splitter and connecting the HP all-in-one directly to the telephone wall jack.

● Try connecting a working phone and phone cord to the telephone wall jack

that you are using for the HP all-in-one and check for a dial tone. If you do not

hear a dial tone, contact your telephone company and have them check the

line.

● Try to send or receive a test fax. If you can send or receive a fax successfully,

there might not be a problem.

After you resolve any problems found, run the fax test again to make sure it passes

and your HP all-in-one is ready for faxing.

The phone cord connected to correct port on fax test failed

Solution

The phone cord is plugged into the wrong port on the back of the HP all-in-one.

1 Using the phone cord supplied in the box with your HP all-in-one, connect one

end to your telephone wall jack, then connect the other end to the port labeled

"1-LINE" on the back of your HP all-in-one.

Note If you use the "2-EXT" port to connect to the telephone wall jack, you

will not be able to send or receive faxes. The "2-EXT" port should only

be used to connect other equipment, such as an answering machine or a

telephone.

2 After you have connected the phone cord to the port labeled "1-LINE", run the

fax test again to make sure it passes and your HP all-in-one is ready for

faxing.

3 Try to send or receive a test fax.

The fax line condition test failed

Solution

● Make sure you connect your HP all-in-one to an analog phone line or you will

not be able to send or receive faxes. To check if your phone line is digital,

connect a regular analog phone to the line and listen for a dial tone. If you do

not hear a normal sounding dial tone, it might be a phone line set up for digital

phones. Connect your HP all-in-one to an analog phone line and try sending

or receiving a fax.

● Check the connection between the telephone wall jack and the HP all-in-one to

make sure the phone cord is secure.

● Make sure you have correctly connected the HP all-in-one to the telephone

wall jack. Using the phone cord supplied in the box with your HP all-in-one,

connect one end to your telephone wall jack, then connect the other end to the

Chapter 16

182 HP Photosmart 2600/2700 series all-in-one

Troubleshooting information

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

HP Photosmart 2700 series Seite 185

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von HP Photosmart 2700 series

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info