Bedienungsanleitung HP Photosmart C6340 (Seite 33 von 39) (Englisch)

563891

Zoom out

Zoom in

Vorherige Seite

1/39

Nächste Seite

To check a wireless connection

1. Make sure that the wireless radio on your computer is turned on.

2. If you are not using a unique network name (SSID), then it is possible that your wireless computer

could be connected to a nearby network that is not yours. The following steps can help you

determine if your computer is connected to your network.

a. Depending on your operating system:

• Windows XP: Click Start, point to Control Panel, point to Network Connections, and

then select View/Details.

Windows XP: Click Start, point to Settings, point to Control Panel, point to Network

Connections, and then select View/Details.

• Windows Vista: Click Start, point to Control Panel, point to Network Connections,

and then click View Network Status and Tasks.

Leave the network dialog box open while you continue to the next step.

b. Disconnect the power cord from the wireless router. The connection status of your computer

should change to Not Connected.

c. Reconnect the power cord to the wireless router. The connection status should change to

Connected.

If you are unable to get your computer connected to your network, contact the person who set up

your network or the router manufacturer as there might be a hardware issue with either your router

or computer.

If you are able to access the Internet, you can also access the HP Network Assistant at

http://

www.hp.com/sbso/wireless/tools-setup.html?jumpid=reg_R1002_USEN for help in setting up a

network.

Step 2: Make sure that the HP All-in-One is connected to your network

If your product is not connected to the same network as your computer, you will not be able to use

the product over the network. Follow the steps described in this section to find out if your product is

actively connected to the correct network.

A: Make sure the product is on the network

To see if the product is connected to the network:

▲ If the product is connected to a wired (Ethernet) network, check the two Ethernet indicator lights

on the top and bottom of the RJ-45 Ethernet jack on the back of the product. The lights indicate

the following:

• Top light: If the light is lit solid green, the product is connected to the network, and

communications have been established. If the light is off, there is no network connection.

• Bottom light: If the yellow light flashes, data is being sent or received by the product over

the network.

▲ If the product is connected to a wireless network, print the product Network Configuration Page,

and then check the Network Status and URL.

To print the Network Configuration Page

a.Press Setup.

b. Press the down arrow button until Network is highlighted, and then press OK.

c. Press the down arrow button until View Network Settings is highlighted, and then press

OK.

d. Press the down arrow button until Print Network Configuration Page is highlighted, and

then press OK.

This prints the Network Configuration Page.

Network troubleshooting 31

Troubleshooting and support

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

HP Photosmart C6340 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von HP Photosmart C6340

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info