212590
29
Zoom out
Zoom in
Vorherige Seite
1/42
Nächste Seite
Scanner Error Message Recovery Process
04 Follow these steps to resolve the error:
1. Check the USB connection between the scanner and the
computer. For more help, see Check the cables.
2. Verify that the scanner is correctly enumerated on the host. If
not, try uninstalling and then reinstalling the software. For more
information, see the HP Scanjet N8400 series Setup and
Support Guide.
3. If the problem persists, contact HP Support. For more
information, see Contact HP Support.
05 Press the Power Save button to turn the scanner off, and then turn
the scanner on again by pressing one of the front panel buttons. If
the message is still displayed, contact HP Support. For more
information, see Contact HP Support.
06 Press the Power Save button to turn the scanner off, and then turn
the scanner on again by pressing one of the front panel buttons. If
the message is still displayed, contact HP Support. For more
information, see Contact HP Support.
07 Press the Power Save button to turn the scanner off, and then turn
the scanner on again by pressing one of the front panel buttons. If
the message is still displayed, contact HP Support. For more
information, see Contact HP Support.
Scanner initialization or hardware problems
Scanner does not start
Scanner has stopped working correctly
Scanner does not start
If you receive an error message similar to “Scanner initialization failed” or “Scanner not
found” when trying to use the scanner, follow these steps:
1. Close the scanning software, if it is open.
2. Disconnect the USB cable that connects the scanner to the computer.
3. Press the Power switch to the off position.
4. Shut down the computer operating system, turn the computer off, wait 60 seconds,
and then turn the computer back on.
5. Press the Power switch to the on position.
6. Reconnect the USB cable that connects the computer and the scanner, making sure
that the USB cable is connected to the back of the scanner correctly.
After 30 seconds, the scanner display should show Ready. If the display does not
show Ready, see the printed Setup and Support guide that came with the scanner.
(continued)
Scanner initialization or hardware problems 27
29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für HP scanjet n8420 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info