522346
38
Zoom out
Zoom in
Vorherige Seite
1/160
Nächste Seite
28
Transom Mount - Side Imaging®
Overview
If you will be installing a Side Imagin transom mounted transducer, use
the procedures in this section. There are two pieces to the transducer mount
assembly: the pivot, and the bracket. Your transducer comes with a two-piece
metal and plastic bracket assembly. There are several procedures you will have
to perform in order to install a transom-mounted transducer. They are:
Determine transducer mounting location
Mount the bracket to the boat
Attach the pivot to the transducer
Mount the transducer pivot assembly to the bracket
Adjust the running position of the transducer
Route the transducer cable
Perform a final test of the transom transducer installation
1. Locating the transducer mounting location
NOTE: If transom mounting is not possible because of a stepped hull or
cavitation noise, trolling motor installation may be an option. See Trolling Motor
Transducer Installation for more information.
1. First, determine the best location on the transom to install the
transducer. Consider the following to find the best location:
It is very important to locate the transducer in an area which is relatively
free of turbulent water. As a boat moves through the water, turbulence
is generated by the weight of the boat, and the thrust of the propeller(s)
- either clockwise or counter-clockwise. This turbulent water is normally
confined to areas immediately aft of ribs, strakes or rows of rivets on the
bottom of the boat, and in the immediate area of the propeller(s).
Clockwise propellers create more turbulence on the port side. On
outboard or inboard/outboard boats, it is best to locate the transducer
at least 15" (380 mm) to the side of the propeller(s).
The best way to locate turbulence-free water is to view the transom
while the boat is moving. This method is recommended if maximum
high-speed operation is a high priority. If this is not possible, select a
location on the transom where the hull forward of this location is
smooth, flat and free of protrusions or ribs.
Deadrise Angle
Areas of Possible Turbulence
Rivets Strakes
Transom Hull
Stepped Hull
Step Rib
38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Humminbird 858C wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info