Bedienungsanleitung Hunter ACC-2 (Seite 15 von 52) (Englisch)

685908

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Built on Innovation

Basic Programming and Setup

INTELLIGENT CURRENT SENSING

ACC2 has no articial programming limits preventing

overlapping programs and stations. The controller senses

how much electrical current is being drawn, and will suspend

stations automatically if the combined current threatens the

transformer.

It is also possible to set controller and station limits (Stations,

Station Limits) to control how many outputs may operate at

once.

A conventionally wired ACC2 may run as many as 14 Hunter

solenoids (including any P/MV outputs) simultaneously before

suspending additional stations. Environmental factors or

higher-draw solenoids may cause the overcurrent protection

to activate at lower station counts.

It is possible to view the current draw of each station in the

Diagnostics menu.

RUN TIMES

You can access Run Times from the programming menu, or

from the so key shortcuts from the Start Times screen. This

allows you to set up an entire program (start times, run times,

and water days) from the same menu.

Verify that you are in the correct program, by number or

name.

Select the Run Type eld, and select Station or Block (“Blocks”

are described in detail in the Stations Menu section. Blocks

replace “SSGs” in the original ACC). Press the dial to select the

type.

Dial to the Number eld. Press and dial to select station or

block number. Press to enter.

Dial to the Run Time eld, press to select, and dial to enter the

run time (from 1 minute to 12 hours). You can also enter run

times in seconds, by dialing to the: SS eld (seconds), which is

adjusted separately.

You may continue to enter any station numbers, in any order,

in the same way.

Show Edit Tools (Shortcuts): Press the so key for Show Edit

Tools. If you are running stations in numerical order, you can

use the so key for Fill Down. This will automatically add 1 to

the previous station number, and copy the run time on the

next line. For example, if you entered Station 1, 5 minutes, and

then pressed Fill Down, it would add Station 2 for 5 minutes

on the next line. This is a shortcut for copying sequential run

times very quickly.

You can also Delete any item from the list. Scroll to the item,

and press Delete.

You can also Insert an item above any selected line in the list.

Scroll to an item, and press Insert Line, and a blank line will

appear above it.

ACC2 can run any station or block in any order. Example: you

could insert station 3 between stations 1 and 2. The program

would run 1, 3, 2, in that order.

Adjusted Run Times: The Adjusted Run Times show the

eects of the current Seasonal Adjust settings on the base

run time. If a run time is set to 10 minutes, but Seasonal

Adjust is at 50%, the Adjusted Run Time will show 5 minutes.

The Seasonal Adjust amount is not changed in this screen,

but can be set from the Programs menu, or automatically by a

Solar Sync sensor.

When all the Run Times for the program have been set, press

Back or Home to exit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hunter ACC-2 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hunter ACC-2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info