Bedienungsanleitung Hunter ACC (Seite 11 von 100) (Englisch)

685907

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

meTal CabIneT, Wall mounT InsTallaTIon ...............................

Tools required:

• Long drill bit and extension

• Philips screwdriver or bit (for use with long

extension) – magnetic recommended

• Wire strippers

31"

(80

)

acepac

k D

Location Requirement: A) a switch or circuit-breaker

shall be included in building installations; B) the switch

or breaker shall be in close proximity to the controller,

and within easy reach of the operator; C) the switch or

breaker shall be marked as the disconnecting device for

the controller.

Avoid direct exposure to sprinkler spray.

Do not install controller within 20" (7 m) of

high-voltage electrical sources, such as service

transformers, pump station motors, etc.

Shaded or partially shaded areas are preferable to

prolonged direct sunlight.

The ACC controller is relatively heavy, about 30 lbs/13.6 kg

in the metal wall mount configuration. Mounting includes

a positioning hanger to assist with installation.

Mounting hardware has been included, but it is the

installer’s responsibility to insure that adequate hardware

is used for the physical location.

ACC is approximately 15½" (40 cm) wide. Allow another

15½" (40 cm) to the left of the controller for the door to

open freely.

Before mounting, it is easier to remove the metal cabinet

door. Swing the door open, grasp the top securely, and

push up on the bottom of the door, near the lower hinge.

The hinges should disengage and the metal door can be

removed.

Positioning Hanger

Mounting Holes

Remove the facepack assembly from the controller.

1. Open the facepack door using the recess on the

right.

2. Disconnect the gray ribbon cable from the back of

the facepack. Pull gently on the ribbon cable; a slight

rocking motion may help disengage the connector.

3. Push up on the upper door hinge, and tilt the door

so that it disengages the hinge posts. Remove the

facepack and set aside in a safe location.

4. OPTIONAL: Locate the positioning hanger in the

upper center of the controller’s location on the wall,

leaving adequate clearance for the opened door to

the left.

5. Drill a pilot hole for the anchor and insert.

6. Install one #10 (5 mm) screw in this hanger position,

leaving approximately ¼" (6 mm) out of the anchor

to allow the controller to hang from this screw.

7. Hang the controller from the keyhole slot in the

positioning hanger.

8. Place a level on the top of the controller cabinet and

level.

9. Locate the 3 mounting holes in the cabinet. These

are visible from the front, with the facepack

removed, in deep recesses in the top two corners,

and another shallow recess in the bottom center.

10. Mark each of these 3 locations and install anchors.

11. Reposition controller on the hanger and use a long

screwdriver or drill extension (3"/75 mm) with

magnetic tip to install the remaining 3 screws, one

at each anchor position, and secure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hunter ACC Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hunter ACC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info