Bedienungsanleitung Hunter ACC (Seite 88 von 100) (Englisch)

685907

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

wait period has elapsed or the radio carrier signal stops,

with no more tones.

A longer DTMF wait allows slower typing speeds of the

command on the radio. The trade-off is that the longer

wait means that it will take longer for the action to be

carried out (in other words, if the Wait is 5 seconds, it will

be 5 full seconds after the command has been sent before

the sprinkler turns on).

This setting is not shown if there is no radio. This setting

does not affect ICR remote commands.

MR DEFAULT RUN TIME (RADIO ONLY)

Default = 30 Minutes. This sets the automatic run time

for any station or SSG that is started by a Maintenance

Radio command, if no run time has been specified in

the On command. It is possible to turn a station or SSG

on without specifying a run time, and this setting will

automatically turn them off after the specified time if they

are not turned off by an Off comand. The Default Run Time

can be changed in 1 minute increments up to a maximum

of 60 minutes. This setting is not shown if there is no radio

and does not affect ICR remote commands.

MODEM TYPE

Indicates presence of a telephone modem in the Com

module. This display is informational and cannot be

changed from the Com module.

COUNTRY CODE

If a telephone modem is detected, the country code may

need to be changed to work with regional data modem

requirements. The default setting is “0” and for most

countries countries this is the correct selection.

If your country appears on the following list, change the

code display to the number shown:

Country Code

Australia 2

Czech Republic 3

Hong Kong 1

Hungary 1

India 1

Indonesia 1

Israel 1

Japan 4

North Korea 1

Malaysia 1

New Zealand 5

Philippines 1

Poland 1

Singapore 1

Slovenia 1

South Africa 6

Vietnam 1

To change the country code, press Enter and the code will

be highlighted. Use the + or – buttons to select the code,

and press Enter. The code will now be set.

HWIM

Indicates presence of a Hardwire Interface Module

(ACC-HWIM) installed in the controller. “None” indicates

no HWIM has been found, “Installed” indicates that the

HWIM is installed and has been detected. This display

is informational and cannot be changed from the Com

module.

ENTER DIAGNOSTICS

To use the built-in communications diagnostics, press the

Enter button at this display.

This will allow you to select from the following diagnostic

functions (use the up or down arrow buttons to move

through the choices).

Communications Status display [MOD RAD HW]

Pressing the left arrow button at any time will show a

status display for communications, showing transmit and

receive activity for each communications type. The display

shows: MOD RAD HW #, indicating Modem, Radio,

Hardwire, and number of data packets sent.

Under each item MOD, RAD, and HW, the letter T shows

transmit activity and R shows receiving data for that

communications component. The symbol * shows other

radio traffic (“carrier detect”).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hunter ACC Seite 88

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hunter ACC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info