Bedienungsanleitung Hunter Wireless Rain-Clik - Rain Sensor (Seite 1 von 2) (Englisch)

685893

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Wireless Rain-Clik

™

Rain Sensors

Installation Instructions

INTRODUCTION

The Wireless Rain-Clik™ acts as a switch to break the circuit to the solenoid

valves of the irrigation system when it has rained. This allows the timer to

advance as scheduled, but keeps the valves from opening the water ﬂow. Once

the Wireless Rain-Clik has dried sufﬁciently, the switch closes again to allow for

normal operation.

The Wireless Rain/Freeze-Clik includes a freeze sensor that is designed to

keep the system from operating at or below 3°C (37°F). At temperatures above

3°C, it will close the circuit for normal sprinkler operation.

MOUNTING

Standard Mounting:

Using the screws provided with in the package, mount the Wireless Rain-Clik

on any surface where it will be exposed to unobstructed rainfall, but not in

the path of sprinkler spray. The switch housing portion must be upright (as

pictured), but the swivel-bracket can be moved for mounting on any angles

surface. Loosen the locknut and screw before swiveling the bracket, and then

re-tighten.

Gutter Mount (SGM Sold Separately):

The sensor gutter mount can be purchased as an optional accessory for your

Wireless Rain-Clik (order p/n SGM). The SGM allows the Wireless Rain-Clik to

be mounted directly to the side of a gutter. To install your Wireless Rain-Clik on

a gutter, Remove the screw, nut, and standard metal extension arm supplied

with the Wireless Rain-Clik, and reinstall the screw and gutter mount. Position

the gutter mount on the edge of the gutter and twist the thumbscrew to secure

it in place.

Helpful Hints for Mounting:

A. Choose a location

such as on the side of

a building or post. The

closer the Wireless

Rain-Clik is to the

controller, the better

reception will be.

DO NOT EXCEED

300 feet.

B. Correct placement

of the Wireless Rain/

Freeze-Clik model is

important for accurate

temperature sensing.

The best location

would be out of direct

sunlight.

C. As described in the

“Operation” section

of this manual, “reset

rate” refers to the

amount of time it takes

the Wireless Rain-Clik

to dry out sufﬁciently

for the sprinkler

system to be allowed

to come back on. The

mounting location will

affect this rate and

should be taken into

consideration should

extreme conditions

exist. For example,

mounting the Wireless

Rain-Clik on a very

sunny, southern end

of a building may

cause the Wireless Rain-Clik to dry out sooner than desired. Similarly,

mounting on the northern end of a building with constant shade may keep

the Wireless Rain-Clik from drying soon enough.

Transmitters/Sensor

• Nothing to set up with this unit after installation

• The unit can be tested stand-alone as follows: press and hold the post on

the quick response section. Within 3 seconds of pressing and holding this

post down, the LED

protruding from the

potting should blink

once. Release the

post, within 3 seconds

the LED should blink

once again. (Figure 1)

Receiver

• Using the hardware

included, mount the

receiver to the wall

(use included wall

anchors if needed).

Make sure to put the

rubber cover/gasket

under the unit when attaching it in an outdoor location.

WIRING TO YOUR IRRIGATION SYSTEM

WARNING! This unit is designed to be installed in conjunction with 24VAC

circuits only. Do not use with 110 or 220VAC circuits.

Receiver Installation,

SRC Controller:

(See Figure 2)

1. Attach the two yellow

wires to the AC terminals

of the SRC (polarity does

not matter).

2. Attach the blue wire to the

RS terminal.

3. Attach the white wire to

the “C” terminal.

4. Attach the valve common

wire to the RS terminal.

Receiver Installation,

Pro-C, ICC, and EC

Controllers: (See Figure 3)

1. Attach the two yellow

wires to the AC terminals

of the controller (polarity

does not matter).

2. Attach the blue wire to

one SEN terminal and

the white wire to the

other SEN terminal of the

controller.

Receiver Installation, Other

Controllers:

A. Normally Closed

Sensor Applications

(See Figure 4)

1. Attach the two yellow

wires to the AC terminals

of the controllers (polarity

does not matter).

2. To attach the receiver

to this type of controller,

attach the blue wire and

the white wire to the

sensor terminals of the

controller, or in-line with

the valve common.

B. Normally Open Sensor

Applications

1. A few controllers on the

market require a normally

open rain sensor. To

attach the receiver to

this type of controller,

attach the blue wire and

the orange wire to the

controller’s sensor input.

Gutter

Mount

(Optional)

Standard

Mount

Figure 1

Manually depress the spindle at

the top of the Wireless

Rain-Clik

Wireless

Rain Sensor

Hunter SRC

Figure 2

R RS C 1ACAC 2 3

Common Wire

to all Valves

Red light indicates

sensor is bypassed

GREEN = Sensor is dr

RED = Sensor is wet

SENSOR BYPASS

SENSOR STATUS

WIRELESS

RAIN SENSOR

Press to bypass, press

again to re-enabl

Figure 3

Wireless

Rain Sensor

Hunter ICC/Pro-C/EC

SEN

TEST

P MV

REM

Red light indicates

sensor is bypassed

GREEN = Sensor is dr

RED = Sensor is wet

SENSOR BYPASS

SENSOR STATUS

WIRELESS

RAIN

SENSOR

RAIN SENSOR

Press to bypass, press

again to re-enabl

Other

Controllers

Figure 4

P MVC

Wireless

Rain Sensor

AC AC

Common Wire

to all Valves

Used for normally

open sensor

applications

Red light indicates

sensor is bypassed

GREEN = Sensor is dr

RED = Sensor is wet

SENSOR BYPASS

SENSOR STATUS

WIRELESS

RAIN SENSOR

Press to bypass, press

again to re-enable

Hunter Wireless Rain-Clik - Rain Sensor Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info