Bedienungsanleitung Hunter XC (Seite 5 von 17) (Englisch)

685866

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

SEN C P 1 2 3 4 5 6 7 8

RST

24VAC

BAT

Valve Common Wire

Connect the Two

Transformer Wires to

the Two AC Terminals

Valve 1

Valve 2

Valve 3

Valve 4

Valve

Wires

MOUNTING THE CONTROLLER TO WALL

NOTE: The indoor XC is not waterproof or weather resis-

tant, and must be installed indoors or in a protected area.

1. Secure one screw into the wall. Install screw anchors if attaching

to drywall or masonry wall.

2. Slide the keyhole on top of the controller over the screw.

3. Secure the controller in place by installing screws in the holes

below the terminal strip.

Do not plug transformer into power source until control-

ler is mounted and all valve wiring has been connected.

CONNECTING VALVES AND TRANSFORMER

Installation of the XC should only be done by trained personnel.

1. Route valve wires between the control valve location and controller.

2. At valves, attach a common wire to either solenoid wire on all

valves. This is most commonly a white colored wire. Attach a

separate control wire to the remaining wire of each valve. All wire

connections should be done using waterproof connectors.

3. Route the valve wires through the conduit. Attach the conduit

through the bottom right side of the controller.

4. Secure the white valve common wire to the C (Common) screw on

the terminal strip. Attach each of the individual valve control wires

to the appropriate station terminals and tighten their screws.

5. Indoor Models: route the transformer cable through the hole on

the left side of the controller and connect the wires to the two

screws marked 24VAC.

Outdoor Models: transformer wires are already connected to the

AC terminals so all that is required is to connect primary power to

the junction box (see below).

E – High Voltage Wiring (Outdoor Model only)

NOTE: XC outdoor models are water and weather resis-

tant. Connecting the outdoor XC to primary AC power

should only be done by a licensed electrician following

all local codes. Improper installation could result in

shock or fire hazard.

1. Route AC power cable and conduit through the ½" (13mm) conduit

opening on the left side bottom of the cabinet.

2. Connect one wire to each of the two wires inside the junction box.

The ground wire should be connected to the green wire. Wire nuts

are provided to make these connections. Note: For –E models

only: Connect the wires to the AC terminal block inside the junc-

tion box. AC supply wires must be 14 AWG (1.85 mm) or larger

with appropriate circuit breaker for the wire size. A switch or cir-

cuit-breaker shall be included in the building installation (in close

proximity to the controller, within easy reach of the operator) and

marked as the disconnecting device for the equipment.

3. Replace the junction box cover.

ACTIVATING THE BATTERY

After installing your XC make sure to remove the bat-

tery contact insulator to allow the XC to keep time in

the event of a power outage.

ENG

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hunter XC Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hunter XC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info