Bedienungsanleitung Hunter XC (Seite 12 von 17) (Englisch)

685866

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

MANUAL-ONE STATION

MANUAL-ALL STATIONS

ALL

SEASONAL ADJUSTMENT

ENG

Seasonal Adjustment

Seasonal Adjust is used to make global run time changes without

re-programming the entire controller. To use the seasonal adjustment

feature:

1. Turn the dial to the SEASONAL

ADJUSTMENT position.

2. The display will now show a flashing number

followed by a %, as well as the bar graph which

always remains on the display. Press the or

button to adjust the percentage of the seasonal adjustment. Each

bar on the graph represents 10%. This feature can adjust the con-

troller from 10% to 150% of the original program.

To view the adjusted run times, simply turn the dial to the RUN TIMES

position, the displayed run time will be updated accordingly as the

seasonal adjustment is made.

NOTE: The controller should always be initially

programmed in the 100% position.

Manually Run a Single Station

1. Turn dial to MANUAL – ONE STATION

position.

2. Station run time will flash in the display. Use the button to

move to the desired station. You may use the or button to

select the amount of time for a station to water.

3. Turn the dial clockwise to the RUN position to run the station (only

the designated station will water, then the controller will return to

automatic mode with no change to the previously set program).

Also see One Touch Start and Advance.

Manually Run All Stations

ALL

1. Turn dial to MANUAL – ALL STATIONS

position.

2. Select program A, B, or C by pressing the button.

3. Station run time will flash in the display. Use the or button

to select the amount of time for a station to water if different from

the run time displayed.

4. Use the button to move to the next station.

5. Repeat steps 3 and 4 to customize each station.

6. Press the button until you reach the station at which you would

like watering to begin.

Turn the dial clockwise to the RUN position (the controller will water

the entire program beginning with the station number last left in the

display, then return to the automatic mode with no change in the

previously set program).

One Touch Manual Start and Advance

You can also activate all stations to water without using the dial.

1. Hold down the button for 2 seconds.

2. This feature automatically defaults to program A. You can select

program B or C by pressing the button.

3. The station number will be flashing. Press the button to scroll

through the stations and use the or button to adjust station

run times. (If no buttons are pressed for a few seconds during

step 2 or 3, the controller will automatically begin watering).

4. Press the button scroll to the station you wish to begin with.

After a 2 second pause, the program will begin. At any time during

the manual cycle, you can use the

or buttons to navigate

from station to station manually.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Hunter XC Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Hunter XC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info