785969

Hurom H-200 Series Seite 12

12
Zoom out
Zoom in
Vorherige Seite
1/13
Nächste Seite
11
Check the following before asking for repair. For follow-up service and any inquiry
you may have while using the product, please contact our Customer Center, or
homepage at http://www.globalhurom.com Check the manufacturer’s number or
the number under the barcode when requesting for follow-up service or parts.
10. Before
Requesting Repair
01. When the product starts
operation, it will make a
"clicking" sound.
02. The product won't operate
with the main body only.
03. Align the safety sensors.
04. The product does not work.
05. The product suddenly
stops running.
06. There are cracks on the
screw and scratch marks on
the upper part of the screw.
07. Juice leaks through the
pulp outlet immediately upon
inserting ingredients.
08. Juice flows back into the
hopper.
09. Juice leaks between the
hopper and the chamber, or
between the chamber and the
main body.
10. I can't open the hopper.
11. The chamber is vibrating
(during juicing).
12. Pulp outlet is covered, but
the pulp comes out.
This is the sound of when the motor and the squeezing screw are connected.
and not a sign of malfunction.
Make sure the chamber set and main body are assembled properly.
Ensure the product is unplugged before assembling or disassembling it.
Make sure they are assembled in accordance with the assembly guide.
Ensure the product is unplugged before assembling or disassembling it.
Check if the power cord is plugged properly.
The machine may not work after prolonged use (30 minutes or longer).
It will resume normal operation once the main body (motor) cools down.
Check if the hopper fits properly.
If the hopper is connected incorrectly, the product will not operate properly.
It will operate only when the lock symbol on the chamber is perfectly aligned
with the assembly guide on the hopper (②-3). Ensure the product is assembled
in accordance with the assembly guide. Refer to the assembly page 6 of the
instruction manual.
Is the hopper overloaded with juicing ingredients, or are the ingredients too big?
Refer to the manual page 9, and activate reverse rotation.
In addition to the straight molding marks on the top and sides of the screw, there
are curved marks that were created while it was being molded.
These marks are normal and they have no impact on your use of the screw.
A little juice may come out of the pulp outlet depending on the ingredient.
This is not a product defect but the result of the characteristics of the ingredient.
The leakage will stop once the product starts running. If the leakage persists,
contact our Customer Service Center.
Did you operate the product with the juice cap closed? Closure of the juice cap
may cause a back flow up to the hopper. If the flow gets clogged even after opening
the juice cap, open the hopper lid and empty out the inside.
Is the hopper silicone ring assembled correctly?
Juice will leak if the chamber silicone ring has been assembled upside down or
incompletely. Check if the silicon rings have been assembled correctly.
There may be excessive pulp remaining inside. If the remaining pulp is discharged
by turning on the machine, or the machine is rotated in reverse for 10 seconds two
or three times, the hopper will open smoothly.
Perhaps you put foreign or solid substances (hard seeds such as persimmon
seeds)? If you have put foreign or solid substances, attempting to run the product
in reverse direction may further damage the component. Thus, contact our
Customer Service Center and request after-sales support.
The product may wobble slightly due to the vibrations produced by the main
body's motor. It may vibrate depending on the ingredient's hardness or toughness.
This is not a malfunction but a normal sign as it is caused by the rotating screw.
The product may seem to vibrate more when juicing solid ingredients (e.g.,
carrots, potatoes, radishes, beets, or kohlrabies) than when juicing soft and
watery ingredients. (e.g., carrot. potato, radish, beet, kohlrabi, etc)
Even if the lever is closed, pulp may still come out naturally.
The velocity and amount of pulp discharge may differ according to the ingredients
used.
4DC010798 사용설명서 통합 H200 Serise 영문_V.01.indd 11 2020-01-28 오후 3:21:56
… 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Hurom H-200 Series wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Hurom H-200 Series

Hurom H-200 Series Bedienungsanleitung - Deutsch, Englisch, Französisch, Italienisch, Spanisch - 29 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info