Bedienungsanleitung Husky C5PRO-H-HU (Seite 30 von 32) (Englisch)

809491

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Freezer Range F5PRO & F10PRO

the door is opened. The switch is located in the top of the door rebate (see Fig. 6 on page 29).

INSTALLING SHELVES

Fit the shelf clips to the ladder racks (see Fig. 2 on page 29) and install the shelves horizontally.

Ensure the clips are located firmly and the shelves are secure before loading the freezer.

FITTING/REMOVING THE ILLUMINATED CANOPY

COMPETENT PERSON ONLY. To fit the canopy, first disconnect the freezer from the power

supply. Remove the right hand door hinge cover. Plug the canopy into the socket that may now

be seen. See Fig. 1 on page 29. Tighten the thumb screws on both sides of the canopy to secure

the canopy to the freezer. Re-connect the freezer to the power supply.

To remove the canopy, first disconnect the freezer from the power supply. Loosen the thumb

screws on both sides of canopy, then pull out the plug for the canopy light – see Fig. 1 on page

29. The canopy may now be removed. Re-fit the right hand door hinge cover. Finally

re-connect the freezer to the power supply.

EASY MAINTENANCE ACCESS

QUALIFIED ENGINEERS ONLY. Husky freezers are designed for easy maintenance. One

feature is that the compressor, condenser and condenser fan are mounted on an easily-

accessible sliding tray. To access this sliding tray, open the door(s) fully and loosen the two

screws (which have now become accessible) on the top on either side of the kick plate – see Fig

5 on page 29. Remove the kick plate by lifting it up and pulling it forward. Loosen the thumb

screws on either side of the sliding tray – see Fig. 4 on page 29. With caution slide out the sliding

tray no more than 300mm.

COMPRESSOR

QUALIFIED ENGINEERS ONLY. To access the compressor, slide out the sliding tray – see ‘Easy

Maintenance Access’.

CLEANING

The condenser MUST be cleaned quarterly. Carefully remove the kick plate (see above for how

to remove the kick plate) and use a soft brush to clean the condenser.

The external and internal surfaces of the unit should be cleaned regularly. Switch the unit off

and disconnect the plug from the mains socket. Remove the drainage hole cover (see Fig. 3 on

page 29). Clean the external and internal surfaces of the unit with a mild soap solution, then

wipe dry. Replace the drainage hole cover. Do NOT use cleansers containing chlorine or other

harsh cleansing agents, as these can damage the stainless steel surfaces and components. Use

mild soapy water to clean the gasket and seals.

GETTING SERVICE ASSISTANCE

The cooling system is a hermetically sealed circuit and does not require any maintenance other

than regular cleaning (see ‘Cleaning’).

If the unit fails to work, first check the power supply. If you cannot locate the reason for the

failure, please contact your supplier, stating the model and serial number of the cabinet. You

may find this information on the rating plate, which is affixed inside the unit on the top right-hand

interior wall.

International PRO upright manual 240317 EDITION 2 v2.indd 30 28/03/2017 08:34

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husky C5PRO-H-HU Seite 30

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info