Bedienungsanleitung Husqvarna 115iPT4 (Seite 18 von 276) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

733999

Zoom out

Zoom in

Vorherige Seite

1/276

Nächste Seite

General information about how to adjust the

depth gauge setting

The depth gauge setting (C) decreases when you

sharpen the cutting tooth (A). To keep maximum cutting

performance you must remove filing material from the

depth gauge (B) to receive the recommended depth

gauge setting. See

Technical data on page 22

for

instructions about how to receive the correct depth

gauge setting for your saw chain.

WARNING: The risk of kickback increases if

the depth gauge setting is too large!

To adjust the depth gauge setting

Before you adjust the depth gauge setting or sharpen

the cutters, refer to

General information about how to

sharpen the cutters on page 17

, for instructions. We

recommend you to adjust the depth gauge setting after

each third operation that you sharpen the cutting teeth.

We recommend that you use our depth gauge tool to

receive the correct depth gauge setting and bevel for the

depth gauge.

1. Use a flat file and a depth gauge tool to adjust the

depth gauge setting. Only use Husqvarna depth

gauge tool to get the correct depth gauge setting and

bevel for the depth gauge.

2. Put the depth gauge tool on the saw chain.

Note:

See the package of the depth gauge tool for

more information about how to use the tool.

3. Use the flat file to remove the part of the depth

gauge that extends through the depth gauge tool.

To adjust the tension of the saw chain

WARNING: A saw chain with an incorrect

tension can come loose from the guide bar

and cause serious injury or death.

A saw chain becomes longer when you use it. It is

important to adjust the tension of the saw chain regularly

to make sure that it is correct. Do a check of the tension

of the saw chain before you operate the product. Tighten

the saw chain as tightly as possible, but it must be

possible to pull the saw chain around freely by hand.

Note: A new saw chain has a running-in period. Do a

check of the tension more frequently during this period.

1. Turn the locking knob counterclockwise to unlock the

chain tension adjuster.

2. Turn the chain tension adjuster clockwise to tighten

the saw chain. Apply as much tension to the saw

chain as possible. It must be tight against the guide

bar.

3. Make sure that you can pull the saw chain around

freely by hand and that it does not hang from the

guide bar.

4. Turn the locking knob clockwise to lock the chain

tension adjuster.

To lubricate cutting equipment

WARNING:

Poor lubrication of cutting

equipment may cause the chain to snap,

which could lead to serious, even fatal

injuries.

WARNING: Do not use waste oil! Waste oil

is dangerous for persons, the product and

for the environment.

18 707 - 003 - 04.03.2019

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna 115iPT4 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info