Bedienungsanleitung Husqvarna 122HD45 (Seite 18 von 532) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

467953

Zoom out

Zoom in

Vorherige Seite

1/532

Nächste Seite

18 – English

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the

Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s

Manual. More extensive work must be carried out by an authorized service workshop.

Maintenance Before use:

After 40

hours in use

After 100

hours in use

Clean the outside of the machine. After each time the machine is used

Make sure the throttle trigger lock and the throttle function correctly

from a safety point of view.

In order to reduce the risk of ﬁre, dirt, leaves and surplus lubricant, etc

must be cleaned from the mufﬂer, exhaust pipe and engine.

Check that the stop switch works correctly. X

Check that the blades do not move when the engine is idling. X

Check that the blades are undamaged and show no signs of cracking

or other damage. Replace the blades if necessary.

Check that the blade guard is not damaged or distorted. Replace the

blade if the blade guard is bent or damaged.

Replace the cutting unit if it is bent or damaged. X

Check that the hand guard is not damaged. Replace the guard if

damaged.

Check that nuts and screws are tight. X

Check that there are no fuel leaks from the engine, tank or fuel lines. X

Clean the air ﬁlter and oil it in.

Clean more often if conditions are exceptionally dusty.

(25 tim).

Check the starter and starter cord. X

Check that the vibration damping elements are not damaged. X

Clean the outside of the spark plug. Remove it and check the electrode

gap. Adjust the gap to 0.5 mm or replace the spark plug. Check that

the spark plug is ﬁtted with a suppressor.

Clean the machine’s cooling system. X

Clean the outside of the carburettor and the space around it. X

Fill the gear housing with grease. This should be carried out

approximately every 25 working hours.

Check that the screws that hold the blades together are correctly

tightened.

Check and clean the spark arrestor mesh on the mufﬂer (only applies

to mufﬂers ﬁtted with a catalytic converter).

Clean the inside of the fuel tank. X

Check the inside of the fuel ﬁlter for any dirt or if the fuel hose has any

cracks or other defects. Replace if necessary.

Check all cables and connections. X

Check the clutch, clutch springs and the clutch drum for wear. Replace

if necessary by an autorized service workshop.

Replace the spark plug. Check that the spark plug is ﬁtted with a

suppressor.

H1153993-26,122HD45,60#4ACBF.fm Page 18 Tuesday, January 4, 2011 8:31 AM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna 122HD45 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info