Bedienungsanleitung Husqvarna 135 Mark II (Seite 15 von 460) (Alle Sprachen)

734154

Zoom out

Zoom in

Vorherige Seite

1/460

Nächste Seite

Assembly

WARNING: Read and understand the safety

chapter before you assemble the product.

To assemble the guide bar and saw

chain

1. Remove the bar nuts and the clutch cover. Remove

the transportation guard (A). (Fig. 39)

2. Put the guide bar above the bar bolts. Steer the

guide bar to its most rear position.

3. Put on protective gloves.

4. Lift the saw chain above the drive sprocket and

engage it in the groove on the guide bar. Start on the

top edge of the guide bar. (Fig. 40)

5. Make sure that the edges of the cutters are turned

forward on the top edge of the guide bar.

6. Assemble the clutch cover and steer the chain

adjuster pin to the hole in the guide bar.

7. Make sure that the drive links of the saw chain fit

correctly on the drive sprocket. Also make sure that

the saw chain is correctly engaged in the groove in

the guide bar.

8. Tighten the guide bar nuts finger.

9. Turn the chain tensioning screw clockwise to tighten

the saw chain. Tighten the saw chain until it does not

hang from below the guide bar, but you can turn it

easily by hand. (Fig. 41) (Fig. 42)

10. Hold up the end of the guide bar and tighten the bar

nuts with the combination wrench. (Fig. 43)

• Examine the chain tension frequently after you

assemble a new saw chain and until the saw

chain has been run-in.

• Examine the chain tension regularly. Correct

chain tension results in good performance and a

long life.

Operation

WARNING: Read and understand the safety

chapter before you operate the product.

To use fuel

CAUTION: This product has a two-cycle

engine. Use a mixture of gasoline and two-

cycle engine oil. Make sure to use the

correct quantity of oil in the mixture.

Incorrect ratio of gasoline and oil can cause

damage to the engine.

Fuel mixture ratio

The fuel mixture ratio for the gasoline and two-cycle

engine oil is 50:1 (2%)

Gasoline

Two-cycle engine oil

1 U.S. Gal. 77 ml (2.6 oz)

1 UK Gal. 95 ml (3.2 oz)

5 l 100 ml (3.4 oz)

To make the fuel mixture

1. Determine the correct quantity of gasoline and

engine oil (mixture ratio 50:1). Do not make more

than 30 days quantity of fuel mixture. See

Fuel

mixture ratio on page 15

2. Add half of the gasoline quantity to a clean fuel

container with an antispill valve.

CAUTION: Do not use gasoline with

more than 10% ethanol concentration

(E10). This can cause damage to the

product.

CAUTION: Do not use gasoline with an

octane number less than 90 RON (87

AKI). This can cause damage to the

product.

Note: Use gasoline with a higher octane number if

you frequently use the product at continuously high

engine speed.

3. Add the full quantity of the two-cycle engine oil to the

fuel container.

CAUTION: Always use air-cooled two-

cycled engine oil of high quality. Other

oils can cause damage to the product.

4. Shake the fuel mixture to mix the contents.

5. Add the remaining gasoline quantity to the fuel

container.

6. Shake the fuel mixture to mix the contents.

7. Fill the fuel tank of the product with the fuel mixture.

See

Fuel mixture ratio on page 15

862 - 002 - 03.12.2018

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna 135 Mark II Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info