Bedienungsanleitung Husqvarna 140e (Seite 17 von 420) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

477604

Zoom out

Zoom in

Vorherige Seite

1/420

Nächste Seite

ASSEMBLY

English – 17

1154580-38 Rev.1 2011-12-05

Fitting the bar and chain

135, 140

Check that the chain brake is in disengaged position by

moving the front hand guard towards the front handle.

(38)

Unscrew the bar nut and remove the clutch cover (chain

brake). Take off the transportation ring (A).

(39)

Fit the bar over the bar bolt. Place the bar in its rearmost

position. Place the chain over the drive sprocket and in the

groove on the bar. Begin on the top side of the bar.

(40)

Make sure that the edges of the cutting links are facing

forward on the top edge of the bar.

Mount the clutch cover and remember to ﬁt the chain

adjuster pin in the hole in the bar. Check that the drive

links of the chain ﬁt correctly over the drive sprocket and

that the chain is correctly located in the groove in the bar.

Tighten the bar nut with your ﬁngers.

Tension the chain by turning the chain tensioning screw

cloc

kwise using the combination spanner. The chain

should be tensioned until it does not sag from the

underside of the bar.

(27)

The chain is correctly tensioned when there is no slack on

the underside of the bar, and it can still be turned easily

by hand. Tighten the bar nut with the combination spanner

while holding up the tip of the bar.

(28)

When ﬁtting a new chain, the chain tension has to be

checked frequently until the chain is run-in. Check the

chain tension regularly. A correctly tensioned chain

ensures good cutting performance and long life.

(25)

135e, 140e, 140e TrioBrake

Check that the chain brake is in disengaged position by

moving the front hand guard towards the front handle.

(38)

Loosen the chain tensioner wheel and remove the clutch

cover (chain brake). Remove the transport guard. (A)

(41)

Fit the bar over the bar bolts. Place the bar in its rearmost

position. Place the chain over the drive sprocket locate it

in the groove on the bar. Begin on the top edge of the bar.

(40)

Make sure that the edges of the cutting links are facing

forward on the top edge of the bar.

Mount the clutch cover and remember to ﬁt the chain

adjuster pin in the hole in the bar. Check that the drive

links of the chain ﬁt correctly over the drive sprocket and

that the chain is correctly located in the groove in the bar.

Tension the chain by turning the wheel down (+). The

chain should be tensioned until it does not sag from the

underside of the bar

(31)

The chain is correctly tensioned when it does not sag from

the underside of the bar, but can still be turned easily by

hand. Hold up the bar tip and tighten the bar knob by

turning the knob clockwise.

(32)

When ﬁtting a new chain, the chain tension has to be

checked frequently until the chain is run-in. Check the

chain tension regularly. A correctly tensioned chain

ensures good cutting performance and long life.

(25)

Fitting a spike bumper

To ﬁt a spike bumper – contact your service agent. (42)

WARNING! Always wear gloves, when

working with the chain.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna 140e Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info