Bedienungsanleitung Husqvarna 236e (Seite 13 von 464) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

477598

Zoom out

Zoom in

Vorherige Seite

1/464

Nächste Seite

GENERAL SAFETY PRECAUTIONS / ASSEMBLY

English – 13

1154212-26 Rev.3 2012-02-22

• Check that the bar tip sprocket turns freely and that the

lubricating hole in the tip sprocket is not blocked. Clean

and lubricate if necessary.

If the chain lubrication system is still not working after

carr

ying out the above checks and associated measures

you should contact your service agent.

Chain drive sprocket

The clutch drum is ﬁtted with a Spur sprocket (the chain

sprocket is welded on the drum).

Regularly check the degree of wear on the drive sprocket.

Replace if wear is e

xcessive. Replace the drive sprocket

whenever you replace the chain.

Checking wear on cutting equipment

Check the chain daily for:

• Visible cracks in rivets and links.

• Whether the chain is stiff.

• Whether rivets and links are badly worn.

Replace the saw chain if it exhibits any of the points above.

We recommend you compare the existing chain with a new

chain to decide how badly the e

xisting chain is worn.

When the length of the cutting teeth has worn down to only

4 mm the chain must be replaced.

Bar

Check regularly:

• Whether there are burrs on the edges of the bar.

Remo

ve these with a ﬁle if necessary.

(15)

• Whether the groove in the bar has become badly worn.

Replace the bar if necessary.

(16)

• Whether the tip of the bar is uneven or badly worn. If a

hollow forms on the underside of the bar tip this is due

to running with a slack chain.

• To prolong the life of the bar you should turn it over daily.

Fitting the bar and chain

Check that the chain brake is in disengaged position by

moving the front hand guard towards the front handle.

Remove the knob and remove the clutch cover (chain

ake). Take off the transportation ring (A).

(17)

Fit the bar over the bar bolts. Place the bar in its rearmost

position. Place the chain over the drive sprocket locate it in

the groove on the bar. Begin on the top edge of the bar.

(18)

Make sure that the edges of the cutting links are facing

forward on the top edge of the bar.

Fit the clutch cover (chain brake) and locate the chain

adjuster pin in the cut-out in the bar

. Check that the drive

links of the chain ﬁt correctly on the drive sprocket and that

the chain is in the groove on the bar.

(19)

Tension the chain by turning the wheel down (+). The chain

should be tensioned until it does not sag from the

underside of the bar.

(12)

The chain is correctly tensioned when it does not sag from

the underside of the bar, but can still be turned easily by

hand. Hold up the bar tip and tighten the bar knob by

turning the knob clockwise.

(13)

When ﬁtting a new chain, the chain tension has to be

checked frequently until the chain is run-in. Check the

chain tension regularly. A correctly tensioned chain

ensures good cutting performance and long life.

(20)

Fitting a spike bumper

To ﬁt a spike bumper – contact your service agent.

WARNING! Most chain saw accidents

happen when the chain touches the

operator.

Wear personal protective equipment.

See instructions under the heading

Personal protective equipment.

Do not tackle any job that you feel you

are not adequately trained for. See

instructions under the headings

Personal protective equipment, How to

avoid kickback, Cutting equipment and

General working instructions.

Avoid situations where there is a risk of

kickback. See instructions under the

heading Machine

′′

s safety equipment.

Use the recommended protective

equipment and check its condition. See

instructions under the heading General

working instructions.

Check that all the chain saw safety

features are working. See instructions

under the headings General working

instructions and General safety

precautions.

WARNING! Switch off the engine before

carrying out any checks or maintenance.

The stop switch automatically returns to

the start position. In order to prevent

unintentional starting, the spark plug

cap must be removed from the spark

plug when assembling, checking and/or

performing maintenance.

Always wear gloves, when working with

the chain, in order to protect your hands

from injury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna 236e Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info