Bedienungsanleitung Husqvarna 450 II (Seite 27 von 120) (Englisch, Portugiesisch, Spanisch)

579277

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

(Fig. 51)

• To cut on the push stroke is when you cut with the

top of the guide bar. The saw chain pushes the

product in the direction of the operator.

(Fig. 52)

WARNING: If the saw chain is caught in

the trunk, the product can be pushed at

you. Hold the product tightly and make

sure that the kickback zone of the guide

bar does not touch the tree and causes a

kickback.

(Fig. 53)

To use the cutting technique

WARNING: Use full throttle when you cut

and decrease to idle speed after each cut.

CAUTION: Engine damage can occur if the

engine runs for too long at full throttle

without load.

1. Put the trunk on a saw horse or runners. (Fig. 54)

WARNING: Do not cut trunks in a pile.

That increases the risk of kickback and

can result in serious injury or death.

2. Remove the cut pieces from the cutting area.

WARNING: Cut pieces in the cutting

area increase the risk of kickback and

that you can not keep your balance.

To use the spiked bumper

1. Push the spiked bumper into the trunk of the tree.

2. Apply full throttle and rotate the product. Keep the

spiked bumper against the trunk. This procedure

makes it easier to apply the force necessary to cut

through the trunk. (Fig. 55)

To cut a trunk on the ground

1. Cut through the trunk on the pull stroke. Keep full

throttle but be prepared for sudden accidents. (Fig.

56)

WARNING: Make sure that the saw

chain does not touch the ground when

you complete the kerf.

2. Cut approximately ⅔ through the trunk and then

stop. Turn the trunk and cut from the opposite side.

(Fig. 57)

To cut a trunk that has support on one end

WARNING: Make sure that the trunk does

not break during cutting. Obey the

instructions below.

(Fig. 58)

1. Cut on the push stroke approximately ⅓ through the

trunk.

2. Cut through the trunk on the pull stroke until the two

kerfs touch. (Fig. 59)

To cut a trunk that has support on two ends

WARNING: Make sure that the saw chain

does not get caught in the trunk during

cutting. Obey the instructions below.

(Fig. 60)

1. Cut on the pull stroke approximately ⅓ through the

trunk.

2. Cut through the remaining part of the trunk on the

push stroke to complete the cut. (Fig. 61)

WARNING: Stop the engine if the saw chain

gets caught in the trunk. Use a lever to open

up the kerf and remove the product. Do not

try to pull the product out by hand. This can

result in injury when the product suddenly

breaks free.

To use the limbing technique

Note:

For thick branches, use the cutting technique.

Refer to

To use the cutting technique on page 27

WARNING: There is a high accident risk

when you use the limbing technique. Refer

Kickback information on page 25

for

instructions how to prevent kickback.

WARNING: Cut limbs one by one. Be careful

when you remove small limbs and do not cut

bushes or many small limbs at the same

time. Small limbs can get caught in the saw

chain and prevent safe operation of the

product.

Note: Cut the limbs piece by piece if it is necessary.(Fig.

62)

1. Remove the limbs on the right side of the trunk.

a) Keep the guide bar on the right side of the trunk

and keep the body of the product against the

trunk.

b) Select the applicable cutting technique for the

tension in the branch. (Fig. 63)

1286 - 002 - 03.06.2020

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna 450 II Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna 450 II

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info