733974
21
Zoom out
Zoom in
Vorherige Seite
1/36
Nächste Seite
2. Attach the blade guard (A) onto the shaft, refer to
To
assemble the trimmer guard on page 20
.
A
B
D
E
F
G
C
3. Install the drive disc (B) on the output shaft.
4. Turn the output shaft until one of the holes in the
drive disc aligns with the related hole in the gear
housing.
5. Tighten the locking bolt (C) with the hex key to lock
the shaft.
6. Put the blade (D) and support cup (E) on the output
shaft.
7. Put the cup washer (F) on the output shaft.
8. Install the nut (G). Hold the shaft of the wrench near
the blade guard as much as possible. To tighten the
nut, you must turn the wrench counterclockwise
which is the opposite direction of rotation. Tighten
the nut to a torque of 35-50 Nm (3.5-5 kpm).
To attach and remove the locknut
WARNING:
Stop the engine, use protective
gloves and be careful around the sharp
edges of the cutting attachment.
A locknut is used to attach some types of cutting
attachments. The locknut has a left thread.
To attach, tighten the lock nut in the opposite
direction to the direction of rotation of the cutting
attachment.
To remove the locking nut, undo the lock nut in the
same direction as the cutting attachment rotates.
To loose and tighten the locknut, use a socket
spanner with a long shaft. The arrow in the picture
shows the area where you should operate the socket
spanner.
WARNING: When you loose and tighten
the locknut there is a risk of injury from
the teeth of the saw blade. You should
therefore always ensure that your hand
is shielded by the blade guard when you
do this.
Note: Make sure that you can not turn the locknut by
hand. Replace the nut if the nylon lining does not have a
resistance of a minimum of 1.5 Nm. The nut should be
replaced after it has been put on approximately 10
times.
To adjust the harness
WARNING:
The product must always be
correctly attached to the harness. Do not
use a defective harness.
1. Put on the harness.
757 - 003 - 24.06.2020
21
21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Husqvarna 520iRX wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Husqvarna 520iRX

Husqvarna 520iRX Bedienungsanleitung - Deutsch, Holländisch, Französisch - 108 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info