Bedienungsanleitung Husqvarna 524R (Seite 28 von 36) (Englisch)

579290

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

28 – English

MAINTENANCE

Maintenance schedule

The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the

Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s

Manual. More extensive work must be carried out by an authorized service workshop.

Maintenance

Daily

maintenance

Weekly

maintenance

Monthly

maintenance

Clean the outside of the machine. X

Check that the harness is not damaged. X

Check that the suspension ring is not damaged. X

Make sure the throttle trigger lock and the throttle function correctly

from a safety point of view.

Check that the stop switch works correctly. X

Check that the handle and handlebar are undamaged and secured

correctly.

Check that the cutting attachment does not rotate at idle. X

Clean the air ﬁlter. Replace if necessary. X

Check that the guard is undamaged and not cracked. Replace the

guard if it has been exposed to impact or is cracked.

Check that the blade is correctly centred, is sharp, and is not cracked.

An off-centre blade will cause vibration that could result in damage to

the machine.

Check that the trimmer head is undamaged and not cracked. Replace

the trimmer head if necessary.

Check that the locking nut of the cutting equipment is tighten correctly. X

Check that nuts and screws are tight. X

Check that there are no fuel leaks from the engine, tank or fuel lines. X

Check that the transport guard for the blade is intact and that it can

be secured correctly.

Check the engine oil level and top up if necessary. X

Check the starter and starter cord. X

Check that the vibration damping elements are not damaged. X

Clean the outside of the spark plug. Remove it and check the

electrode gap. Adjust the gap to 0,6-0,7 mm or replace the spark plug.

Check that the spark plug is ﬁtted with a suppressor.

Clean the machine’s cooling system. X

Clean or replace the spark arrestor mesh on the mufﬂer (only applies

to mufﬂers without a catalytic converter).

Clean the outside of the carburettor and the space around it. X

Check that the bevel gear is ﬁlled three-quarters full with lubricant. Fill

if necessary using special grease.

Check the fuel ﬁlter from contamination and the fuel hose from cracks

or other defects. Replace if necessary.

Check all cables and connections. X

Check the clutch, clutch springs and the clutch drum for wear.

Replace if necessary by an autorized service workshop.

Replace the spark plug. Check that the spark plug is ﬁtted with a

suppressor.

Check and clean the spark arrestor mesh on the mufﬂer (only applies

to mufﬂers ﬁtted with a catalytic converter).

Change the engine oil. X

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna 524R Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna 524R

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info