Bedienungsanleitung Husqvarna 525PT5S (Seite 12 von 28) (Englisch)

734457

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

3. Shake the fuel mixture.

4. Add the remaining quantity of gasoline to the

container.

5. Carefully shake the fuel mixture.

CAUTION: Do not mix fuel for more than 1

month at a time.

To fill the fuel tank

1. Clean the area around the fuel tank cap.

2. Shake the container and make sure that the fuel is

fully mixed. Use a fuel container with an anti-spill

valve.

3. Fill the fuel tank.

4. Tighten the fuel tank cap carefully.

5. Move the product 3 m (10 ft) or more away from the

refueling area and fuel source before starting.

CAUTION: Contamination in the tanks

causes malfunction. Clean the fuel tank and

chain oil tank regularly and replace the fuel

filter one time a year or more.

To do a run-in

• During the first 10 hours of operation, do not apply

full throttle without load for extended periods.

To use the correct chain oil

WARNING:

Do not use waste oil, which can

cause injury to you and the environment.

Waste oil also causes damage to the oil

pump, the guide bar and the saw chain.

WARNING: The saw chain can break if the

lubrication of the cutting equipment is not

sufficient. Risk of serious injury or death to

the operator.

WARNING: This product has a function that

lets the fuel run out before the chain oil. Use

the correct chain oil for this safety function to

operate correctly. Speak to your servicing

dealer when you select your chain oil.

Note: This product has an automatic chain lubrication

system. You can also adjust the oil flow. Refer to

adjust chain lubrication on page 21

• Use Husqvarna chain oil for maximum saw chain life

and to minimise environmental damage. If

Husqvarna chain oil is not available, we recommend

you to use a standard chain oil.

• Use a chain oil with good adherence to the saw

chain.

• Use a chain oil with correct viscosity range that

agrees with the air temperature.

CAUTION: If the oil is too thin, it runs out

before the fuel. In temperatures below

0°C/32°F some chain oils become too

thick, which can cause damage to the oil

pump components.

• Use the recommended cutting equipment. Refer to

Accessories on page 24

To use the product

• Hold the product as close to your body as possible to

get the best balance. Use the harness to support the

weight of the machine and make it easier to handle.

• Make sure that the tip does not touch the ground.

• Do not rush the work, but work steadily until all the

branches have been cut back cleanly.

• Always slow the engine to idle speed after each

working operation. Long periods at full throttle

without any load on the engine can lead to serious

engine damage.

• Always work at full throttle.

• Whenever possible position yourself so that you can

make the cut at right angles to the branch.

90°

• Do not work with the shaft held straight out in front of

you (like a fishing rod) as this increases the apparent

weight of the cutting attachment.

712 - 003 - 18.02.2019

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna 525PT5S Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna 525PT5S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info