Bedienungsanleitung Husqvarna 535i XP (Seite 14 von 40) (Englisch)

733798

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Operation

Introduction

WARNING: Read and understand the safety

chapter before you use the product.

To do a function check before you use

the product

1. Do a check of the chain brake (A) to make sure that

it operates correctly and that it is not damaged.

2. Do a check of the rear right hand guard (B) to make

sure that it is not damaged.

3. Do a check of the power trigger and the power

trigger lockout (C) to make sure that they operate

correctly and that they are not damaged.

4. Do a check of the keypad (D) to make sure that it

operates correctly.

5. Make sure that there is no oil on the handles (E).

6. Do a check to make sure that all parts are correctly

attached and not damaged or missing.

7. Do a check of the chain catcher (F) to make sure

that it is attached correctly.

8. Do a check of the chain tension (G).

9. Charge the battery (H) and make sure that it is

correctly attached to the product.

10. Make sure that the saw chain stops when you

release the power trigger.

B H F G

To use the correct chain oil

WARNING:

Do not use waste oil, which can

cause injury to you and the environment.

Waste oil also causes damage to the oil

pump, the guide bar and the saw chain.

WARNING: The saw chain can break if the

lubrication of the cutting equipment is not

sufficient. Risk of serious injury or death to

the operator.

WARNING: Use the correct chain oil for this

function to operate correctly. Speak to your

servicing dealer when you select your chain

oil.

• Use Husqvarna chain oil for maximum saw chain life

and to prevent negative effects on the environment.

If Husqvarna chain oil is not available, we

recommend you to use a standard chain oil.

• Use a chain oil with good adherence to the saw

chain.

• Use a chain oil with correct viscosity range that

agrees with the air temperature.

CAUTION: In temperatures below 0°C/

32°F some chain oils become too thick,

which can cause damage to the oil pump

components.

• Use the recommended cutting equipment. Refer to

Accessories on page 34

• Remove the cap to the chain oil tank.

• Fill the chain oil tank with chain oil.

• Attach the cap carefully.

Note: To see where the chain oil tank is on you product,

refer to

Product overview on page 2

To connect the battery charger

1. Connect the battery charger to the voltage and

frequency that is specified on the rating plate.

2. Put the plug in a grounded socket outlet. The LED

on the battery charger flashes green one time.

Note:

The battery does not charge if the battery

temperature is more than 50 °C/122 °F. If the

temperature is more than 50 °C/122 °F, the battery

charger makes the battery become cool before the

battery charges.

To connect the battery to the battery

charger

Note:

Charge the battery if it is the first time that you use

it. A new battery is only 30% charged.

14 958 - 010 - 24.04.2020

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna 535i XP Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna 535i XP

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info