Bedienungsanleitung Husqvarna 535RX (Seite 24 von 40) (Englisch)

477472

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

The grease in the bevel gear does not need to be

changed unless repairs are carried out.

To attach and remove the locknut

WARNING: Stop the engine, use protective

gloves and be careful around the sharp

edges of the cutting attachment.

A locknut is used to attach some types of cutting

attachments. The locknut has a left thread.

•To attach, tighten the locknut in the opposite

direction to the direction of turning of the cutting

attachment.

• To remove the locknut, loosen the locknut in the

same direction as the cutting attachment rotates.

• To loosen and tighten the locknut, use a socket

wrench with a long shaft. The arrow in the picture

shows the area where you can operate the socket

wrench.

WARNING: When you loosen and

tighten the locknut, there is a risk of

injury from the blade. You must always

make sure that the blade guard prevents

injury to your hand when you do this.

Note: Make sure that you can not turn the locknut by

hand. Replace the nut if the nylon lining does not have a

resistance of a minimum of 1.5 Nm. The locknut must be

replaced after it has been put on approximately 10

times.

To examine the spark plug

CAUTION: Always use the recommended

spark plug type. Incorrect spark plug type

can cause damage to the product.

• Examine the spark plug if the engine is low on

power, is not easy to start or does not operate

correctly at idle speed.

•To decrease the risk of unwanted material on the

spark plug electrodes, obey these instructions:

a) Make sure that the idle speed is correctly

adjusted.

b) Make sure that the fuel mixture is correct.

c) Make sure that the air filter is clean.

• If the spark plug is dirty, clean it and make sure that

the electrode gap is correct, refer to

Technical data

on page 28

• Replace the spark plug if it is necessary.

To adjust the engine

Follow these instructions if the engine does not operate

correctly.

1. Attach an approved cutting attachment, see

Accessories on page 29

2. Start the engine.

3. Operate the product in usual conditions for 3

minutes.

4. Lift the cutting attachment in the air and apply full

throttle for 30 seconds. If a trimmer head is used,

make sure that the trimmer line is cut to correct

length by the guard knife.

Note: Do not cut grass or branches during this step.

5. Operate the product in usual conditions to make sure

that the engine operates correctly.

6. If the engine does not operate correctly, do step 4

and 5 again 3 times.

7. Let your Husqvarna dealer adjust/repair the product

if the engine does not operate correctly after you

have done all these steps.

To adjust the low speed needle (L)

• Turn the low speed needle clockwise until stop.

Note: If the product has a bad acceleration capacity

or if the idle speed is not correct, turn the low speed

needle counterclockwise. Turn the low speed needle

until the acceleration capacity and idle speed is

correct.

24 1069 - 005 -

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna 535RX Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna 535RX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info