Bedienungsanleitung Husqvarna 550 XP Mark II (Seite 12 von 40) (Englisch)

734157

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

and with large force, which throws the product in the

direction of the operator.

Kickback always occurs in the cutting plane of the guide

bar. Usually, the product is thrown against the operator

but can also move in a different direction. It is how you

use the product when the kickback occurs that causes

the direction of the movement.

A smaller bar tip radius decreases the force of the

kickback.

Use a low kickback saw chain to decrease the effects of

kickback. Do not let the kickback zone touch an object.

WARNING: No saw chain fully prevents

kickback. Always obey the instructions.

Common questions about kickback

• Will the hand always engage the chain brake during

a kickback?

No. It is necessary to use some force to push the

front hand guard forward. If you do not use the force

necessary, the chain brake will not be engaged. You

must also hold the handles of the product stable with

two hands during work. If a kickback occurs, it is

possible that the chain brake does not stop the saw

chain before it touches you. There are also some

positions in which your hand can not touch the front

hand guard to engage the chain brake. An example

of this is in the felling position.

• Will the inertia release mechanism always engage

the chain brake during kickback?

No. First, the chain brake must operate correctly.

Refer to

Maintenance and checks of the safety

devices on the product on page 22

for instructions

about how to do a check of the chain brake. We

recommend you to do this each time before you use

the product. Second, the force of the kickback must

be large to engage the chain brake. If the chain

brake is too sensitive, it can engage during rough

operation.

• Will the chain brake always protect me from injury

during a kickback?

No. The chain brake must operate correctly to give

protection. The chain brake must also be engaged

during a kickback to stop the saw chain. If you are

near the guide bar, it is possible that the chain brake

does not have time to stop the saw chain before it

hits you.

WARNING: Only you and the correct

working technique can prevent kickbacks.

To start the product

To prepare to start with a cold engine

WARNING: The chain brake must be

engaged when the product is started to

decrease the risk of injury.

1. Move the front hand guard forward to engage the

chain brake.

2. Pull the start/stop switch (A) out and up to set it in

choke position.

3. Press the air purge bulb (B) about 6 times or until

fuel starts to fill the bulb. It is not necessary to fill the

air purge bulb fully.

(A)

(B)

4. Continue to

To start the product on page 13

for

more instructions.

To prepare start with a warm engine

WARNING:

The chain brake must be

engaged when the product is started to

decrease the risk of injury.

12 544 - 005 - 10.05.2019

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna 550 XP Mark II Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna 550 XP Mark II

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info