Bedienungsanleitung Husqvarna 553RBX (Seite 7 von 32) (Englisch)

734098

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

• Avoid all usage which you consider to be beyond

your capability.

• Do not use the product unless you are able to call for

help in the event of an accident.

• Using an incorrect cutting attachment or an

incorrectly sharpened blade increases the risk of

blade thrust.

• Products fitted with saw blades or grass blades can

be thrown violently to the side when the blade comes

into contact with a fixed object. This is called blade

thrust. A blade thrust can be violent enough to cause

the product and/or operator to be propelled in any

direction, and possibly lose control of the product.

Blade thrust can occur without warning if the product

snags, stalls or binds. Blade thrust is more likely to

occur in areas where it is difficult to see the material

being cut.

• Avoid cutting with the area of the blade between the

12 o'clock and 3 o'clock positions. Because of the

speed of rotation of the blade, blade thrust can occur

if you attempt to cut thick stems with this area of the

blade.

• Mufflers fitted with catalytic converters get very hot

during use and remain so for some time after

stopping. This also applies at idle speed. Contact

can result in burns to the skin. Remember the risk of

fire.

• Only use cutting attachments with the guards we

recommend. Refer to

Accessories on page 26

To do a check of the throttle trigger lockout

The throttle trigger lockout locks the throttle trigger at the

idle position to prevent accidental operation of the

throttle trigger. When you release the handle of the

throttle trigger and the throttle trigger lockout the two

move back to their initial positions.

1. Push the throttle trigger lockout (A). Make sure that

the throttle trigger (B) is released.

2. Make sure that the throttle trigger (B) is locked at the

idle position when the throttle trigger lockout is

released.

3. Push the throttle trigger lockout (A) and make sure

that it goes back to its initial position when you

release it.

4. Make sure that the throttle trigger lockout (A) and the

throttle trigger (B) move freely.

5. Start the product and apply full throttle. Refer to

start the engine on page 17

6. Release the throttle trigger (B) and make sure that

the cutting attachment stops and stays stationary.

WARNING: If the cutting attachment moves

when the throttle trigger is in the idle

position, adjust the idle speed. Refer to

adjust the idle speed on page 21

To do a check of the stop switch

1. Start the engine.

2. Move the stop switch to the stop position and make

sure that the engine stops.

To do a check of the cutting attachment guard

WARNING: An incorrect or defective cutting

attachment guard can cause serious injury.

Refer to

Accessories on page 26

WARNING: Always use the recommended

cutting attachment guard for the cutting

attachment that you use. If an incorrect or

defective cutting attachment guard is

installed, this can cause serious injury. Refer

Accessories on page 26

1104 - 005 - 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna 553RBX Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna 553RBX

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info