Bedienungsanleitung Husqvarna Automower 405X - 2023 (Seite 13 von 52) (Englisch)

819083

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

3 Installation

3.1 Introduction - Installation

WARNING: Read and understand the

safety chapter before you install the product.

CAUTION: Use original spare parts and

installation material.

Note: Refer to www.husqvarna.com for more

information about installation.

3.2 Main components for installation

The installation involves the following components:

• A robotic lawn mower that mows the lawn

automatically.

• A charging station, which has 3 functions:

• To send control signals along the boundary

wire.

• To send control signals along the guide wire

so that the product can follow the guide wire

to specific remote areas in the garden and

can find its way back to the charging station.

• To charge the product.

• A power supply, which is connected to the

charging station and a 100-240V power outlet.

• Loop wire, which is laid around the work area

and around objects and plants that the product

must not run into. The loop wire is used both as

boundary wire and guide wire.

3.3 To prepare for installation

Read the installation chapter before you start the

installation. Prepare the installation carefully to make the

product operate satisfactorily.

• Make a blueprint of the work area and include all

obstacles. This makes it easier to examine where

to put the charging station, the boundary wire and

the guide wire.

• Make a mark on the blueprint where to put the

charging station, the boundary wire and the guide

wire.

• Make a mark on the blueprint where the guide wire

connects to the boundary wire. Refer to

To install

the guide wire on page 18

• Fill in holes in the lawn to make it level.

CAUTION: Holes with water in

the lawn can cause damage to the

product.

• Cut the grass before you install the product. Make

sure that the grass is maximum 10 cm / 3.9 in.

Note: The first weeks after installation the sound level

when the product cuts the grass can be higher than

usual. The sound level decreases after some time.

3.4 Before the installation of the wires

You can select to attach the wires with stakes or bury

them. You can use the 2 procedures for the same work

area.

CAUTION: If you use a dethatcher

in the work area, bury the boundary wire

and the guide wire to prevent them from

damage.

3.4.1 To examine where to put the charging

station

• Keep a minimum 3 m / 10 ft. of free space in front

of the charging station. Refer to

To examine where

to put the guide wire on page 17

• Keep a minimum of 150 cm / 60 in. of free space

to the right and left of the center of the charging

station.

• Put the charging station near a power outlet.

• Put the charging station on a level surface.

• The baseplate of the charging station must not be

bent.

max. 5 cm / 2"

• If the work area has two parts separated with a

steep slope, we recommend to put the charging

station in the lower section.

1650 - 006 - 20.02.2023 Installation - 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna Automower 405X - 2023 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna Automower 405X - 2023

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info