Bedienungsanleitung Husqvarna Automower 410XE NERA - 2024 (Seite 13 von 48) (Englisch)

819071

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

• Keep a minimum of 150 cm / 60 in. of free space

to the right and left of the center of the charging

station.

• Put the charging station near a power outlet.

• Put the charging station on a level surface.

• The baseplate of the charging station must not be

bent.

• If the work area has two parts separated with a

steep slope, we recommend to put the charging

station in the lower section.

• Put the charging station in an area with protection

from the sun.

• For Automower® 310E NERA, put the charging

station where there is Wi-Fi coverage to download

new firmware. Refer to

Download firmware over

the air FOTA (Firmware over the air) on page 24

For Automower® 410XE NERA cellular technology

is used for FOTA. You can also select to use Wi-Fi

with FOTA.

• If the charging station is installed on an island,

make sure to connect the guide wire to the island.

3.4.2 To examine where to put the power

supply

CAUTION: Make sure that the blades

on the product do not cut the low-voltage

cable.

CAUTION: Do not put the low-voltage

cable in a coil or below the charging station

plate. The coil causes interference with the

signal from the charging station.

• Put the power supply in an area with a roof and

protection from the sun and rain.

• Put the power supply in an area with good airflow.

• Use a residual-current device (RCD) with a tripping

current of maximum 30 mA when you connect the

power supply to the power outlet.

Low-voltage cables of different lengths are available as

accessories.

3.4.3 To examine where to put the

boundary wire

CAUTION: There must be a barrier of

minimum 15 cm / 6 in. in height between

the boundary wire and water bodies, slopes,

precipices or public roads. This will prevent

damage to the product.

CAUTION: Do not let the product

operate on gravel.

CAUTION: Do not make sharp bends

when you install the boundary wire.

CAUTION: For a careful operation

without noise, isolate all obstacles such as

trees, roots and stones.

The boundary wire must be put as a loop around the

work area. For good cutting results with EdgeCut, it is

necessary to install the boundary wire at the correct

distances to obstacles. The product only cuts with

EdgeCut by the boundary wire. To use EdgeCut around

trees and obstacles, make islands around them. Refer to

To make an island on page 14

. Sensors in the product

sense when the product goes near the boundary wire,

and the product selects a different direction. All parts of

the work area must be maximum 35 m / 115 ft. from the

boundary wire.

• Put the boundary wire around the work area (A).

Adapt the distance between the boundary wire and

obstacles.

2369 - 001 - 05.02.2024 Installation with wire - 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna Automower 410XE NERA - 2024 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna Automower 410XE NERA - 2024

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info