Bedienungsanleitung Husqvarna Automower 450X NERA - 2023 (Seite 20 von 48) (Englisch)

819081

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

4 Settings

This chapter gives information about the settings for

the product that you can make in the Automower®

Connect app. All setting for the product are available in

Automower® Connect. Some settings can also be made

in Automower® Access, refer to

Automower® Access on

page 9

. The product has factory settings but the settings

can be adapted for each work area.

4.1 Schedule

Schedule

you can change the schedule settings for

the product.

The

Schedule

function controls which hours the product

operates. When the product does not operate, it is

parked in the charging station. You can see which hours

and days the product operates in the schedule overview

in the app.

You can set the Schedule if the work area is less

than the maximum area capacity of the product. This

prevents wear on the grass and the product. The factory

schedule setting lets the product operate around the

clock 7 days a week.

To calculate the schedule setting, refer to

To calculate

the schedule setting on page 20

4.1.1 To calculate the schedule setting

1. Calculate the dimension of your lawn in m2 / ft2.

2. Divide the m2 / ft2 of the lawn with the approximate

operation capacity. Refer to table below.

3. The result is equal to the number of hours that the

product must operate each day.

Note: The operation capacity is approximate and is

calculated for flat and open work area. If the work area

has a lot of slopes or obstacles, you need to increase

the

Schedule

settings.

Model Approximate operation capaci-

ty, m2/h / ft2/h

Automower® 320 92 / 990

Automower® 430X 133 / 1430

Automower® 450X 208 / 2240

Example: A lawn of 1000 m2 / 10700 ft2, cut with an

Automower® 320.

1000 m2 / 92 ≈ 11 h.

10700 ft2 / 990 ≈ 11 h.

Days / week h / day Schedule settings

7 11 07:00-18:00 / 7:00

am-6:00 pm

4.2 Cutting height

4.2.1 Adjust the cutting height

The cutting height can be adjusted from 2 cm / 0.8 in. to

6 cm / 2.4 in.

CAUTION: The first weeks after a new

installation, the cutting height must be set to

6 cm / 2.4 in. to prevent damage to the loop

wire. The cutting height can then be lowered

each week.

4.2.2 TargetHeight

Use the TargetHeight function to lower the cutting height

from the maximum cutting height to the specified cutting

height gradually during 10 days. If you change the

cutting height manually during this time it will disable the

TargetHeight function.

4.3 Operation

Operation

you can change the operation settings of

the product.

4.3.1 Spiral cutting

If the product enters an area where it senses the grass

is longer than average, it can change the movement

pattern to

Spiral cutting

. This means that the product

mows in a spiral pattern to faster cut the area with

longer grass. It is possible to set the intensity of the

Spiral cutting

Very low / Low

intensity means that

Spiral

cutting

begins less often.

High / Very high

intensity

means that

Spiral cutting

begins more often.

Note:

Spiral Cutting

does not start in slopes steeper

than 17%.

20 - Settings 2071 - 001 - 29.03.2023

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna Automower 450X NERA - 2023 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna Automower 450X NERA - 2023

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info