Bedienungsanleitung Husqvarna Automower 450X NERA - 2024 (Seite 34 von 52) (Englisch)

819078

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

Message Cause Action

No loop signal

There is no power in the charging station.

The LED indicator on the charging station is

not on.

Examine if the power supply unit or the low-

voltage cable is damaged or not installed

correctly to the power outlet or the charging

station. Examine if there is a power failure or

if a residual-current device is enabled.

The boundary wire is damaged or not instal-

led correctly.

Make sure that the boundary wire is connec-

ted correctly to the charging station. Examine

all splices on the boundary wire. Examine if

there is a break in the boundary wire and

repair if necessary. Refer to

To install the

boundary wire on page 18

ECO mode

is enabled and the loop signal is

disabled when the product is started in the

work area.

Put the product in the charging station and

start the product. To start the product man-

ually in the work area, push the STOP but-

ton before you remove the product from the

charging station.

The boundary wire is crossed on its way to

and from an island.

Make sure that the boundary wire is put

down correctly. Refer to

To install the charg-

ing station on page 17

The product does not find the loop signal

from the charging station.

Put the product in the charging station and

generate a new loop signal. Refer to

New

loop signal on page 24

Disturbances from metal objects (fences, re-

inforcement steel) or buried cables close by.

Try to move the boundary wire and/or make

more islands in the work area to increase the

signal strength.

The product is too far from the boundary

wire.

Redo the installation of the boundary wire so

that all parts of the work area is maximum 35

m / 115 ft. from the boundary wire.

Outside work area

The boundary wire connections to the charg-

ing station are crossed.

Make sure that the boundary wire is connec-

ted correctly to the charging station. Refer to

To install the boundary wire on page 18

The boundary wire is too close to the edge of

the work area.

Make sure that the boundary wire is put

down correctly. Refer to

To install the boun-

dary wire on page 18

The work area is too steep by the boundary

wire.

The boundary wire around an island is not

installed correctly. The boundary wires are

crossed.

Disturbances from metal objects (fences, re-

inforcement steel) or buried cables close by.

Try to move the boundary wire and/or make

more islands in the work area to increase the

signal strength.

The product cannot find the correct loop sig-

nal because of interference with a loop signal

from a different product installation nearby.

Put the product in the charging station and

generate a new loop signal. Refer to

New

loop signal on page 24

Upside down

The product is leaning too much or has

turned over.

Turn the product the right way up.

Mower tilted

The product tilts too much. Move the product to a level area.

34 - Troubleshooting 2071 - 002 - 05.02.2024

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna Automower 450X NERA - 2024 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna Automower 450X NERA - 2024

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info