Bedienungsanleitung Husqvarna CTH224T (Seite 22 von 112) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

477579

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

• From the rear of the tractor, slide the lower clevis assembly

(12) onto the right side bagger support tube (10). Line up the

center hole (13) on upper bracket with the hole in the bagger

support tube (10) and secure lower clevis assembly (12) with

clevis pins (14) and clips (15).

• Install the actuator (16) as shown. Use the spacers (17) to

center the actuator (16) between both the upper and lower

brackets and secure with clevis pins (18) and clips (19).

TO INSTALL BAGGER SPRING LATCH

The bagger spring latches are located on the back plate (1),

one in each of the bottom corners.

Before installing, tractor engine must be shut off and parking

brake engaged.

• Install each bagger spring latch with the loop end (2) down

and facing towards the bagger assembly.

• Place the mounting bolt (3) through the backplate. Place

curved end of the bagger spring latch onto mounting bolt (3)

and secure with nut (4) as shown. Tighten firmly.

BAGGER SPRING LATCH ADJUSTMENT

If the bagger assembly height is adjusted, it may be necessary

to adjust the bagger spring latch. To adjust, remove the nut (4)

and move the bagger spring latch to the appropriate hole in the

backplate (1), ensuring the bagger assembly will be securely

closed. Retighten nut securely.

NOTE: The bottom of the bagger assembly should contact the

loop end so that it is held securely when closed.

TO INSTALL BAGGER FULL LEVER/EXTENSION

Before installation or adjusting, tractor engine must be shut off

and parking brake engaged.

• Remove center discharge chute. (See "To Remove Center

Chute" in section 6 of this manual.)

• Remove bolt (1). Place lever (2) into slot and reinstall bolt

(1). Adjust as needed.

TO ADJUST BAGGER FULL LEVER/EXTENSION

Slide bagger full extension (3) to the desired position.

• For the heaviest/wet grasses, slide extension all the way in.

• For the lightest/driest grasses, pull extension all the way out.

• Route cable assembly (20) between the lower clevis assem-

bly (12) and along bagger support tube (10), and connect the

cable assembly (20).

• Using the switch (21) on the right side fender, fully extend

the actuator (16). Secure any excess cable assembly to

the bagger support tube (10) with the zip ties (22). Retract

the actuator (16) and check to ensure there are no snags or

binds in the cable assembly (20).

• Install the bagger assembly.

NOTE: Both cross tubes (23) on the bagger support weldment

need to be placed onto the top support assemblies (24). Extend-

ing the actuator slightly will help make installation easier. Once

installed, adjust bagger assembly as needed. (See "To Adjust

Bagger" in this section of the manual.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna CTH224T Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info