Bedienungsanleitung Husqvarna DESIGNER EPIC (Seite 13 von 198) (Englisch)

609741

Zoom out

Zoom in

Vorherige Seite

1/198

Nächste Seite

Function Buttons

1. Automatic needle threader

2. Stitch re-start

3. Speed – and +

4. Needle stop up/down

5. Cut function

6. Reverse

7. Start/stop

8. FIX function

9. STOP function

10. Reverse (same functions as #6)

11. Presser foot down and pivot

12. Presser foot up and extra lift

Automatic Needle Threader

See Using the Automatic Needle Threader, page 35 to learn

how to place the thread for automatic needle threading. When

the thread is in place, touch this button to thread the needle

automatically.

To prevent damage to the automatic needle threader, needle,

presser foot or other attached accessories, read the instructions

carefully on how to use the automatic needle threader before

using it.

Stitch Re-Start

When you stop sewing in the middle of a stitch, touch stitch

re-start to begin sewing at the beginning of the stitch. The

stitch or stitch program will remember any special settings

you made.

Speed – and +

All stitches and embroideries in your machine have a pre-set,

maximum allowed sewing speed to provide a good stitch

result.

Touch speed – to decrease the maximum allowed sewing

speed. Touch speed + to increase the maximum allowed

speed again. The machine will never sew faster than the

maximum allowed sewing speed for the selected stitch/

embroidery. Touch speed – or + when the machine is not

running and a pop-up on the screen will indicate the speed

setting. You can set the speed by touching the slider in the

pop-up or by touching the speed – or + buttons. If you

change the speed setting while sewing no pop-up will appear.

Needle Stop Up/Down

Touch needle stop up/down to set the position of the needle

when you stop sewing. The needle will move up or down

when you touch the button. The indicator light is on when

needle stop down is set.

Tip: You can also tap the foot control to raise or lower the needle once

you stop sewing. Tapping the foot control does not change the set stop

position.

Cut Function

Touch the cut function button and your machine cuts the

upper and bobbin threads, raises the presser foot and needle,

and activates the FIX function for the next start.

To cut threads at the end of a stitch or stitch program, touch

the cut function button while sewing. The indicator light will

flash, alerting you that a cut is requested. When the stitch or

stitch program is completed, your machine cuts the upper and

bobbin threads, raises the presser foot and needle, and

activates the FIX function for the next start.

Note: If automatic FIX and selective presser foot lift has been deselected

in temporary sewing settings, FIX function will not be activated and

presser foot will not be raised when using the cut function.

Touch the cut function button when embroidering and your

machine cuts the upper and bobbin threads instantly.

Some optional accessories are attached in the two small

circular holes in the needle plate just above the bobbin cover.

Do not use the cut function when an accessory is attached in

these holes as that may interfere with the automatic thread

cutter located under the needle plate.

1 Introduction 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna DESIGNER EPIC Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna DESIGNER EPIC

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info