Bedienungsanleitung Husqvarna Designer SE - Limited Edition (Seite 16 von 100) (Englisch)

609910

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

1-16

Set it Up

Function Buttons

Stitch Re-start

When having stopped sewing in the middle of a stitch,

touch Re-start to start sewing at the beginning of

the stitch again without having to re-set any special

settings you have made.

IN EMBROIDERY MODE: Used for easy bobbin access, see

page 3-7.

STOP

STOP is used to conclude a stitch. Your Designer SE

Limited Edition À xes the thread and stops automatically

when one stitch or stitch program has been

completed. The button lights up when you touch it.

STOP is cancelled when you touch the button again or

by selecting a new stitch. The button light will go out.

The STOP function can be programmed, see page

2-14.

IN EMBROIDERY MODE: Used for one color embroidery, see

page 3-7.

Fix

FIX is used to tie off a stitch and is automatically

activated when a stitch is selected or when the Selective

Thread Cutter has been used. At the beginning, your

Designer SE Limited Edition sews a few tie-off stitches

and goes on with the selected stitch. Touch FIX while

sewing – Designer SE Limited Edition sews a few tie-

off stitches and stops automatically. The button lights

up when the FIX function is active. By touching the lit

button the function can be turned off. The FIX function

can be programmed (see page 2-14).

IN EMBROIDERY MODE: Touch to baste an outline of the

embroidery area (see page 3-7).

NOTE: Automatic FIX can be cancelled in the Set Menu (see

page 1-25).

Selective Thread Cutter

Touch the button and your Designer SE Limited

Edition cuts the top and bobbin threads, raises the

presser foot and the needle, and activates the FIX

function. To cut before the needle moves to the start

position of next stitch, touch Selective Thread Cutter

while sewing. The button starts Á ashing, indicating that

a cut is requested. The Selective Thread Cutter function

can be programmed, see page 2-14.

NOTE: Designer SE Limited Edition cuts automatically after

Sensor buttonhole stitches. Automatic Selective Thread

Cutter can be cancelled in the Set Menu, see page 1-25.

IN EMBROIDERY MODE: Cuts top and bobbin threads and

raises presser foot. Top thread only is cut automatically at

the color change. When the design is À nished both top and

bobbin threads are cut automatically.

Needle Stop Up/Down

Touch this button to move the needle down or up.

The set ting of the needle stop po si tion is changed

at the same time. The set needle stop position is

indicated by an up or down arrow next to the needle

recommendation on screen. You can also tap the foot

control to raise or lower needle.

IN EMBROIDERY MODE: Used for park position and easy

thread trims (see page 3-8).

Speed

Touch

+ SPEED or ñ SPEED to increase or decrease

the sewing speed. Touch when not sewing and a pop-up

window on the screen indicates the speed set ting. You

can also set the speed by touching the slider in the pop-

up. You can change the speed set ting while sewing but

no pop-up will appear. All stitches in your Designer SE

Limited Edition have a pre-set, recommended sewing

speed. When you select a stitch, your Designer SE

Limited Edition automatically sets the best sewing speed

for that stitch.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna Designer SE - Limited Edition Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna Designer SE - Limited Edition

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info