Bedienungsanleitung Husqvarna Designer SE (Seite 16 von 100) (Englisch)

609909

Zoom out

Zoom in

Vorherige Seite

1/100

Nächste Seite

1-16

Set it Up

Function Buttons

Stitch Re-start

When having stopped sewing in the middle

of a stitch, touch Re-start to start sewing at the

beginning of the stitch again without having to

re-set any special settings you have made.

IN EMBROIDERY MODE: Used for easy bobbin access,

see page 3-7.

STOP

STOP is used to conclude a stitch. Your Designer SE

ﬁ xes the thread and stops automatically when

one stitch or stitch program has been completed.

The button lights up when you touch it. STOP is

cancelled when you touch the button again or

by selecting a new stitch. The button light will

go out. The STOP function can be programmed,

see page 2-14.

IN EMBROIDERY MODE: Used for one color embroidery,

see page 3-7.

Fix

FIX is used to tie off a stitch and is automatically

activated when a stitch is selected or when the

Selective Thread Cutter has been used. At the

beginning, your Designer SE sews a few tie-off

stitches and goes on with the selected stitch. Touch

FIX while sewing – Designer SE sews a few tie-off

stitches and stops automatically. The button lights

up when the FIX function is active. By touching

the lit button the function can be turned off. The

FIX function can be programmed (see page 2-14).

IN EMBROIDERY MODE: Touch to baste an outline of the

embroidery area (see page 3-7).

NOTE: Automatic FIX can be cancelled in the Set

Menu (see page 1-25).

Selective Thread Cutter

Touch the button and your Designer SE cuts the

top and bobbin threads, raises the presser foot

and the needle, and activates the FIX function. To

cut before the needle moves to the start position

of next stitch, touch Selective Thread Cutter while

sewing. The button starts ﬂ ashing, indicating that

a cut is requested. The Selective Thread Cutter

function can be programmed, see page 2-14.

NOTE: Designer SE cuts automatically after Sensor

buttonhole stitches. Automatic Selective Thread

Cutter can be cancelled in the Set Menu, see page

1-25.

IN EMBROIDERY MODE: Cuts top and bobbin threads and

raises presser foot. Top thread only is cut automatically

at the color change. When the design is ﬁ nished both

top and bobbin threads are cut automatically.

Needle Stop Up/Down

Touch this button to move the needle down or

up. The set ting of the needle stop po si tion is

changed at the same time. The set needle stop

position is indicated by an up or down arrow

next to the needle recommendation on screen.

You can also tap the foot control to raise or

lower needle.

IN EMBROIDERY MODE: Used for park position and easy

thread trims (see page 3-8).

Speed

Touch

+ SPEED or − SPEED to increase or

decrease the sewing speed. Touch when not

sewing and a pop-up window on the screen

indicates the speed set ting. You can also set the

speed by touching the slider in the pop-up. You

can change the speed set ting while sewing but no

pop-up will appear. All stitches in your Designer SE

have a pre-set, recommended sewing speed. When

you select a stitch, your Designer SE automatically

sets the best sewing speed for that stitch.

DSE 05 Kap 1.indd 1-16 05-03-14 10.56.54

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna Designer SE Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna Designer SE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info