Bedienungsanleitung Husqvarna E20 (Seite 35 von 36) (Englisch)

609911

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

TROUBLESHOOTING GUIDE

Problem Cause Correction

Upper thread

breaks

1.The machine is not threaded correctly

2.The thread tension is too tight

3.The thread is too thick for the needle

4.The needle is not inserted correctly

5.The thread is wound around the spool

holder pin

6.The needle is damaged

1. Rethread the machine

2. Reduce the thread tension (lower number)

3. Select a larger needle

4. Remove and reinsert the needle (À at side

towards the back)

5. Remove the spool and thread again

6. Replace the needle

Lower thread

breaks

1.The bobbin case is not inserted cor-

rectly

2.The bobbin case is threaded incorrectly

3.The lower thread tension is too tight

1. Remove and reinsert the bobbin case and

pull on the thread. The thread should pull

easily

2. Check both bobbin and bobbin case

3. Loosen lower thread tension as described

Skipped

stitches

1.The needle is not inserted correctly

2.The needle is damaged

3.The wrong size needle has been used

4.The foot is not attached correctly

1. Remove and reinsert needle (À at side

towards the back)

2. Insert a new needle

3. Choose a needle to suit the thread and

fabric

4. Check and attach correctly

Needle

breaks

1.The needle is damaged

2.The needle is not correctly inserted

3.Wrong needle size for the fabric

4.The wrong foot is attached

1. Insert a new needle

2. Insert the needle correctly (À at side to-

wards the back)

3. Choose a needle to suit the thread and

fabric

4. Select the correct foot

Loose

stitches

1.The machine is not correctly threaded

2.The bobbin case is not correctly

threaded

3.Needle/ fabric/ thread combination is

wrong

4.Thread tension wrong

1. Check the threading

2. Thread the bobbin case as illustrated

3. The needle size must suit the fabric and

thread

4. Correct the thread tension

Seams gather

or pucker

1.The needle is too thick for the fabric

2.The stitch length is wrongly adjusted

3.The thread tension is too tight

1. Select a ¿ ner needle

2. Shorten the stitch length

3. Loosen the thread tension

Uneven

stitches,

uneven feed

1.Poor quality thread

2.The bobbin case is wrongly threaded

3.Fabric has been pulled

1. Select a better quality thread

2. Remove bobbin case and rethread and

insert correctly

3. Do not pull on the fabric while sewing, let it

be fed by the feed dogs

The machine

is noisy

1.The machine must be lubricated

2.Fluff or oil have collected on the hook or

needle bar

3.Poor quality oil has been used

4.The needle is damaged

1. Lubricate as described

2. Clean the hook and feed dog as described

3. Only use good quality sewing machine oil

4. Replace the needle

The machine

jams

Thread is caught in the hook Remove the upper thread and bobbin case,

turn the handwheel backwards and forwards

by hand and remove the thread pieces.

Lubricate as described

Intellectual property

VIKING is a trademark of KSIN Luxembourg II, S.ar.l. HUSQVARNA and the “crowned H-

mark” are trademarks of Husqvarna AB.

All trademarks are used under license by VSM Group AB.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Husqvarna E20 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Husqvarna E20

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info